Useful content

How to make a door to the bath with his hands

click fraud protection

Make your own bathroom door can any who have the right tool, special skills, and quite a lot of time and desire.

Bathroom door and x species

Every bath has a few rooms, which makes a variety of functions, so for the protection of each will need its own door. Doors indoor bath should be at least two: the front and the steam room in a special relaxation room.

There are three types of sauna doors:

wooden doors. It is a wooden sheet, which consists of a tongue and groove boards, which are covered with a conventional lining. These doors are usually made with a single frame, but some can do with two frames. Latest in the production of a little more complicated, however have excellent thermal insulation properties;

glass doors. These doors are often set it in the sauna. But now many preference is given to the aesthetic interior full of practicality and expense of buying a door glass;

combined bathroom door. For those people who are able to decide which is better - wood or glass, the optimum will be their special combination. Bottom frame and similar doors made of wood, and all the upper part is a special insert of glass.

instagram viewer

The main features of sauna doors

When you create data door should take into account two main criteria - the heat and the humidity level inside the bath room. The first feature of a door - its size, the second - the materials used, and the last - used furniture.

The size of sauna doors

Making bath doors, all sizes determined by the principle of maximum conservation of heat at the time of opening and closing doors. In this regard, all bathroom doors have a smaller size when compared to the conventional. The required height of the sauna doors - 165-185 cm from the floor, and the width - 65-70 cm. It is worth paying attention to the threshold, the height of which must be greater than 15 cm. However, such small size doors are used solely for steam rooms.

Materials for the proper manufacture of bathroom doors

For sauna doors can also be used glassand wood. The glass must withstand very high temperatures. However, the best material for sauna doors - it's still wood.

Here, as a rule, apply - lime, larch, aspen, oak.

findings

Fittings for doors of bath must be made of materials with very low thermal conductivity and resistance to high humidity. If used, e.g., latches and handles of metal, then the touch can easily get burned. In this connection accessories are usually made of wood.

It is about latches and handles, but the loop is desirable to take the brass, but if you find these fails, the loop of metal be sure to paint special paint against corrosion. Since the bathroom door open it out, the possibility of burns is almost impossible.

Manufacture of bathroom doors

After determining the type of doors, it is already possible to start work on the creation of a special. For beginners, this process may well seem rather complicated, but it is only a matter of experience. If you have never made the door, then you can start to buy cheap board and they will be trained. Next, it will allow you to make the bathroom door without problems.

Since most optimal door for a bath is considered the door of the timber, it is on its example we will look at the whole process of sauna doors. Before the production, door to the bath, as a rule, you need to make the purchase. From the materials we can not do without:

  • decking floorboard (width of 50 mm and a thickness of 30 mm);
  • special pins and screws;
  • lining (dimensions - 12h96 mm);
  • loop (three pieces);
  • timber for binding (size - 60x80 mm).

The tool can not do without:

  • hand-held circular saws;
  • hammer and mallet;
  • router with a set of cutters;
  • screwdriver;
  • clamps;
  • level, caliper, depth gauge, measuring tapes.

Make a door leaf

Manufacturing of doors should always begin with the formation of the web. To do this, do this:

  • You must take special tongue and groove boards and cut them to the desired length.
  • Then, in one of the boards should be cut spike, then fuguetsya surface on both sides of each board, you get a completely flat surface. Usually enough to remove 2 mm in order to achieve the desired result. Ideally turn have smooth board with a thickness of 26 mm.
  • You can start collecting the door leaf. You should first make a rough assembly is inserted into the groove of the board spike the other, at the same time it is necessary to join them as tightly as possible. As a result, you can get the cloth slightly larger dimensions in width than necessary. It's not scary. To get the required fabric width, it will be necessary to cut off a little from the last and the first board.
  • Having measured the right size, the smaller of 60-70 mm from the width of the entire door and mark it on the canvas, it is necessary to remove the first and last board. On the circular saw cut them all superfluous. It is important not to cut the last board side on which the groove and on the first board side, where there is a spike.
  • Further, the board collected in one painting. To do this, on the surface of the bench need to expand the board and insert the spike of one board into a groove of the previous pre-missed groove inside ordinary PVA glue. For a good connection, you must mallet to tamp each board.
  • The canvas is left to dry for two or three days. So that the drying period painting never led, it should be on the workbench securely. For this purpose it is necessary to fix two planks of wood on a workbench, between which is placed longitudinally door leaf. For normal fixation is necessary to drive a wooden wedge between the door and door strap. On top of fabric laid special sheet chipboard and pressed him to the table clamps.
  • After drying, you need to check the web for the presence of small defects. The slots are sealed with a special mixture of sawdust and glue, and all the irregularities are smoothed conventional plane.

Making the fittings and piping doors

While the canvas dries, you can begin creating bolts and knobs as well as the special strapping for doors:

Purchased in advance for strapping bars need to trim to the desired length. Vertical bars should be trimmed according to the height of the door. Those bars that will be placed at the top and bottom of the door, should be slightly less. For example, the door height is 150 cm, then the length of the bars to be bound binding 150 cm. If the door width is about 60 cm, the length of the bars to be bound to the binding of about 53 cm.

  • The precursor bar must select the slot previously obtained. To this end, by end mill and the mill must first choose a deep and narrow groove. Its width - of approximately 26 mm, depth - 25mm. Thereafter, on top of it should be chosen wide, but shallow groove (depth of 10 mm and a width of 50 mm). Such a stepped groove in the piping needed for the web that was trimmed with clapboard. In a must fit paneling and deep will include all stable planks.
  • On the horizontal bars binding by milling step is a spike which corresponds to the groove. At the end you need to collect a box strapping and check the correctness of set square corners. When needs must dotochit groove cutter to get absolutely right angles.
  • To manufacture the bolts and handle necessary to apply trimming boards and bars in advance or acquired workpiece.

Sheathing lining, door assembly

Now it remains only to sheathe canvas lining, assemble wooden sauna doors together and make a box door. To do this, run this:

Door leaf is necessary to process a special tool from rotting.

Then, on the door leaf must outline contour with slightly indented from the edge to about 15 mm, which stands for the edge lining. Next, you need to take the strap lining, cut them up to a certain length and attach them securely to the door. Planck lining has a groove and tenon, so it is enough to dial as previously boards for door leaf. Strips should be fastened to the blade by means of small screws or nails.

This is followed by installation of piping for the entire door panel. To do this, take the bars, their preparation process of putrefaction, then set the vertical and horizontal bars. To all of them sat down on the seat tight enough, you must finish them with a mallet. For imparting greater strength else adding PVA in all grooves of the vertical bars, and all the grooves of the upper bar. The lower the bar, it is desirable to install without glue in order to make it possible to simply remove if necessary. At the end-to-end bars should be binding screw screws: two small bars and three for long.

This is followed by the installation bolts and handles. To do this, you must identify on the door of the place of their installation. The end brackets and bolt handle zasverlivayutsya the holes to a depth of about 4 cm. Then a drill bit of smaller diameter must Drill a through hole, while also capturing the door. Next, you need to take a long screw and screw it all the way. Screws must enter 2.5 cm in the door leaf. We proceed similarly with the hole for the handle. In all holes by mounting it is necessary to insert the cut plug or wooden pin and sanded over normal skin. Just do all the mounting brackets for the dead bolt.

After all this, you can start the creation of the door frame. To do this, use the boards with dimensions of 100x100 mm. To create one box is enough to trim up to a certain length and a quarter by select mills. It is important that the depth of this quarter was higher by approximately 5 mm. This is extremely important, because wood door swells and can easily become jammed in under a constant humidity bath. In addition, we must remember that the vertical upper limit will be slightly smaller than the width of the box, and the threshold height should be at least 10-15 cm. To join the boards of the box on all sides from the bottom rack and top need to cut grooves, and on the edges of the upper limit of the threshold and cut spikes. Before you install the box door, it is necessary to collect and verify the accuracy of all angles gon. If required, it is necessary to dotachit recesses treat special means against rot and get to the door assembly in place.

As easy to install bathroom door

When the doors are fully prepared, we can install them. Installation begins with breaching the doorway of special grooves. They do about 10 mm longer than the width of the door frame, it is necessary to ensure that when installation you can easily correct the location of your door vertically rasperet it with wedges. Then the box is mounted in the grooves. It is important not to confuse, where it will open the door.

Important! It should be recalled - the door should swing open in a bath just outside.

Then you need to have a horizontal top beam and prop up its uprights. After that, the bottom need uklast threshold. level through watching the absolutely vertical position of the box. Well aligned vertically between the frame and the wall all the clearances should be to drive a wedge, it will lock the box in place. Fasten the door frame to the wall using dowels, Drill advance under these special holes. When the box is well secured, you are ready for assembly loops to canvas door. The very first loop should be at a height of about 25 cm from the top of the door, the second - 50 cm, well, and the third - 25 cm from the bottom edge. This will help uberegti your door from warping, especially if your canvas is very heavy. Now it is necessary to hang the door leaf, and around the perimeter of the box to fill a felt roller and repaired all the cracks.

Making the bathhouse door - it is rather difficult, and it is approached with responsibility necessarily need. The truth is the result of the most able to surpass all expectations.

How I struggled with mold on the ceiling in my country house for several years.

Mold is an attack that is not easy to get rid of. One has only to appear on the ceiling or wall o...

Read More

How I built a monolithic-wooden frame house: technology, prices

How I built a monolithic-wooden frame house: technology, prices

Experience is the most valuable information, and doubly when it comes to construction. After all,...

Read More

My WorkPro sapper shovel has arrived. Doing a review

My WorkPro sapper shovel has arrived. Doing a review

Surely numerous travel lovers, fishermen and hunters will not refuse to purchase a universal tact...

Read More

Instagram story viewer