Water Heaters Ariston vs Thermex vs AEG, what to choose?

Why is the cost of a heater 5000, and an analogue of another manufacturer - fifteen thousand?

Electrical water heaters: the main producers

This is not just to make the right decision of buying a reliable heater. Stores offer a variety of manufacturers and models. You can read the article - how to choose a water heater, but a manufacturer, we will discuss below.

There are three well-known manufacturers of electric water heaters. manufacturer Ariston (Russia) manufacturer Thermex (Russia) the AEG Manufacturer

Others will not be considered because they are either little known or not proven to be reliable.

Ariston

It is considered high-quality water heaters, since its origins production from Italy. To date, some models are still manufactured in Italy, such as: Ti-Shape, Ti-Tronic. Functionally no different from its competitors, however, has a convenient form and a nice design. Produced with a tank made of stainless steel, steel coated with silver ions and steel coated fine enamel. Some models have a tank 2 for rapid heating hot water.

Thermex

Italian roots, the production in Russia. Simple functional water heater allows you to manage them as needed without any problems. Some models are equipped with Termex control panels and touch-sensitive buttons. Tanks made of stainless steel, steel with enamel dispersed.

AEG

German production is considered to be the most reliable and durable, but is worth a half times more expensive. The AEG has different modes of operation, including energy saving. The main advantage over other manufacturers of water heaters wall - significantly more insulation. Reservoir coated with corrosion, heater elements of stainless steel.

Each manufacturer cares about how the water heater will be combined with the interior of the room where it will be installed. This is not surprising, the manufacturer is concerned, it is to choose a water heater. Forms of water heaters are diverse, horizontal, vertical, circular, rectangular, elongated, broad, thick, narrow, not deep - your choice. Colors also are different: white, gray, stainless steel, up to changing colored panels and even photo stickers.

cylinder management

water heater control, each manufacturer is not complicated. There are models with a hidden control, to add a special temperature necessary to remove the cover, but already there is to twist the key. There's also a model with buttons, sensors and remote control. LCD installed in some models, most of those water heaters are programmed.

What to choose Ariston vs Thermex vs AEG?

It just so happens that the water heater from any manufacturer can both serve you for a long time, and to bring the cost of repairs and service. In the production of water heaters AEG almost every second element is checked on marriage, on the other hand it is expensive bulky and not always get it to install. Ariston water heaters and Termex marriage checked one out of ten. But they are cheaper and more compact. Therefore, if you have a lot of space and you important savings on electricity and no small importance producer country - definitely take the AEG water heater. If you care about how the water heater will look in the bathroom, a closet, whether it is a compact - or choose Ariston Thermex.

To make sure your water heater is not broke should pay attention to the following recommendations.

Recommendations for the use of water heaters

Such guidelines will the water heater last you longer. That there is no cost for parts, immediately think through filtering water entering the water heater. To clean water from rigid particles it is recommended to install a filter cartridge with a bulb filled with an ion exchange resin or shungit. Ideally set the EMC filter at the inlet to the water heater and even before all the equipment that has ten. Thus, the filter will protect the stain from sticking to it scums.

Each equipment requires maintenance, the water heater in the passport are registered service recommendations once a year. It is necessary to carry out such procedures as lifting TENA and removed from the scale, descaling with the cylinder bottom of the tank. Note that when the strong scale on tene, TEN quickly heated and combusted.

One of the main recommendations - set the heating rate to 60 ° C, since after 60 degrees scum begins to form.

During the disconnection of the heater (when the central hot water supply) is clipped sidebar cylinder, so that the water from the central water does not pass therethrough.

Find out the availability of specialized service centers in your area. Listen carefully to the advice to use water heater from service centers employees, who but they will tell you, a manufacturer of water heaters have to be repaired frequently. Be interested in the availability of spare parts. Otherwise it may be a situation when the water heater broke, and western part of the need to wait.

Never ask installers, plumbers, how best to choose a water heater. Usually they have limited information, often they recommend and install the same manufacturer all.

There is disagreement about to leave the water in the water heater or not. Here, you decide. Drain the water - tank gets oxygen and rust may appear. Do not pour the water - the water begins to stagnate, in this case it is possible for most of its drive through the tank.

A source: https://www.allremont59.ru/inzhenerka/vodosnab/vodonagrevateli-ariston-thermex.html