Useful content

How to make a ground loop for a house: instructions

click fraud protection

Grounding in old private houses is a rather rare thing. Many underestimate its importance before the first circuit or electric shock. But in vain! See below how to ground the wiring of your house yourself and not overpay for it to electricians.

Infographic source: Yandex. Pictures
Infographic source: Yandex. Pictures

What is needed for this?

Required consumables:

  • copper ground wire, cross-section 6 mm (length - from the shield to the junction with the strip);
  • a tip for a wire and a bolt with a nut for it;
  • steel strip 40 * 4 mm - 8 meters;
  • metal pin, round timber, diameter 10 mm - 3 pieces, 3 meters each.

Required inventory: welding machine; Bulgarian; punch or drill; shovels; sledgehammer; other auxiliary tool.

Photo source: https://vm.tiktok.com/JFVxRab/
Photo source: https://vm.tiktok.com/JFVxRab/
Photo source: https://vm.tiktok.com/JFVxRab/
Photo source: https://vm.tiktok.com/JFVxRab/
Photo source: https://vm.tiktok.com/JFVxRab/
Photo source: https://vm.tiktok.com/JFVxRab/
Photo source: https://vm.tiktok.com/JFVxRab/

What should be done?

instagram viewer
  1. Determine the place where the ground loop will be - it should be in the area of ​​the shield.
  2. Dig a straight trench 6 meters long, two bayonets deep (60 cm), 30 cm wide. The location of the trench is best done perpendicular to the wall of the house.
  3. Drive the pins into the ground in the trench in two meter increments, leaving 30 centimeters above the bottom of the trench. The pins can be pre-sharpened with a grinder so that they better go into the ground.
  4. Bend the tops of the pins 10–12 centimeters at a right angle. It is necessary to bend the pin by heating it with a welding machine. The direction of the corner is parallel to the trench towards the wall.
  5. Weld the steel strip (jumper) to the pins. You need to cook well - not with potholders, but put a continuous seam at least 7 centimeters long!
  6. Lead the remaining end of the strip near the wall of the house and secure.
  7. Weld a bolt to the strip, under the lug of the ground wire. Do not leave large seams in the welding area! The tip should fit snugly against the strip.
  8. Bury a trench.
  9. Lead the grounding wire into the shield, connect it to the bus. Attach a ferrule to the other end of the wire.
  10. Lead the wire outside and connect it to the ground loop (securely screw the tip to the welded nut).

The outline is ready, you can use it!

Is the wiring in your house grounded? Write in the comments!


Friends, subscribe to our partner "Kitchen from the inside" Is one of the oldest culinary channels on the Yandex Zen platform. Professional chefs share their secrets. Extraordinary recipes, life hacks in the kitchen and in everyday life, many articles on restaurant topics.

There are already 30 thousand of us! Subscribe to our channel - we are working, so that you receive only useful and relevant information!

Read also:

  • What is wrong with aerated concrete: an overview of the main disadvantages.
  • Stone fences: expensive; beautifully; reliable! Photo collection of original solutions.

Watch the video - Combined chalet on a complex site: frame + rubble stone.

Budget shredders from scrap materials: their own hands

Budget shredders from scrap materials: their own hands

Fotoinstruktsiya: how to make their own hands an inexpensive shredder for grass, leaves and folia...

Read More

Fruiting plants that are easy to grow from bone

Fruiting plants that are easy to grow from bone

When we buy a variety of foreign vegetables or fruit, we often get planting material, almost noth...

Read More

How to rejuvenate adult Spathiphyllum

How to rejuvenate adult Spathiphyllum

Many favorite houseplants. Illustrations for publication taken from the Internet"Women's happines...

Read More

Instagram story viewer