Replacing the old interior door to the new own resources
Consider the sequence of actions to replace the old interior door. Installation work is better to coincide with the repair of the room, which is planned to replace the door. After will be prepared for the ceiling and wall finishing, proceed to the installation of a new door.
Just when choosing a door, without taking into account your preferences in design and price range, consider the size of the door. To do this, measure the old door or doorway itself. Dimensions doors are standard, so choose the one that suits your size range.
Attention!!! A very important point, on what ever you chose, while working independently, door frame must be made of wood rather than chipboard.
Mounting boxes made of chipboard requires experience, otherwise it may lead to the fact that after its foaming box izognot and will have to start all over again.
What do I need to install an interior door?
Tools and materials required to perform the work:
- door with bars to the door frame;
- pen latch and a crown for her tie;
- door hinges;
- construction foam and the foam gun;
- Hacksaw on a tree;
- screwdriver and hammer;
- chisel;
- screwdriver and screws;
- yardstick;
- builder's level, a plumb;
- straps for attaching drywall.
Collection of the door frame and the door to the preparation of the installation
To install the door in front of the reveal is necessary to perform the work on the collection of the door frame and door. You should start with the installation of hinges on the door leaf. Put the door on the edge to avoid damage to the bottom of the use foam, bundled with the door. We are putting a loop alternately from above and below, offset from the edges of the door 20-30 cm and draw out a pencil.
Then, the marked spots are working out neat chisel equal to the depth of the thickness of the loop.
Manufacture and installation of the loop fastener screws (supplied with the door hinges).
We begin collecting door to the side of the box, where the Loop on the door leaf. In the absence of a special tool, it is more expedient to connect the horizontal and vertical part of the box with a perpendicular slit therebetween.
For this part of the door sawn prihlopa connected at both bars, docks to form a right angle and fixed with screws (two more than enough - 50-60 mm). We put the resulting corner of the box to the door, leaving a gap between the door and the casing of 2-3 mm, and shifts the set of loops on the box, marking pencil.
Applied to the reverse side hinges made labels and fasten the loop response to the box, by the method set forth above. Making the second docking an horizontal duct portion, considering the width of the door plus the clearance. The gap between the door and the floor door is 10-15 mm, it is necessary to take into account the width of the floor covering, if it is made after laying door mounting.
Box lock (latch) is performed using a set of a crown. It is attached diagram and method of installation. Insert the return of the castle is similar to installing loops.
Installation of the door frame
Fasten with screws strap for attaching drywall to the frame from the outside (three vertical parts). screws length should be about 10 mm, so as not to damage the face of the door box. This will allow installation without damage to the door frame and give the aesthetic appearance.
Installation in the doorway to make the top corner on the hinge side. Exposed vertical side upper corner of the level, and curled strip marked place under drilling hammer. It is a hole and attached to the wall using anchor nails. Then doing the same steps with the remaining two points of fixation.
Using a plumb line, check that the second vertical side fixed with respect to. Checking if the level of the horizontal bar, and installing the second side. After fixing all brackets, between the door frame and the wall are inserted chopiki that helps to strengthen the structure. Worn door on hinges, and made installation control.
Before foaming of the opening should be laid around the perimeter of the door a few pads to avoid bending the door frame foam. Foaming produced from the bottom up, not a large number, and using gloves. After filling in all of the opening foam, the door is left closed at the time of the foam drying.
Installation of interior doors is almost completed. It remains to make a choice in the design of the door frame. You can use frames, which are attached to the door duct or plaster wall flush with the door frame.
p.s .:My HouseHe is trying to give you the most important, useful information. If you liked the article, please put "like".subscribe to the channel - in front of a lot of useful and interesting information!