A fence made of crushed cinder block and sheet-prof, a fence can build even a novice builder

Every modern man, who has his own house dreams about a beautiful fence that will serve not only protective function, but also will decorate your home. Not every man can build his fence himself, not because he can not, but because they are often faced with such work. Therefore, after reading this article, such a fence can even the novice builder. There is a huge range of titles and types of fences, so each owner is trying to pick a favorite type of fence individually.

Consider that the fence can be constructed brick or crushed cinder block and Prof. sheet. "Picture 8" Initially, you need to decide on the amount of material needed for construction. Take a tape measure and measure the length of the fence, and of course, definitely need to be determined with the height.

Material which is required for the construction of such a fence:

-koloty cinder block or brick (you need to consider how much you need to build the pillars);

-prof sheet metal and screws;

-prof-tube (one chooses as its dimensions Finance);

-armatura for reinforcement under the bump between the bump and pedestals spans (counted sampling length);

A-boards, or waste of old furniture for formwork;

-pesok, gravel and cement.

Once all the material you have available, you can start building. Initially determined place for the future gate. Begin to dig holes for future columns, measuring tape is the same markup, in this case, between the posts made by three meters. Pit themselves should not be less than fifty centimeters in depth, since they will be the maximum load. Take the boards, and cut into a jigsaw or sawing blank necessary for the bar under the formwork. Given the size of a brick or cinder block, with an area defined under bump pedestals, particularly ideal for fifty centimeter pedestal. Twisted all formwork and start to put it on a previously dug pit. Once exposed timbering is necessary to determine the height of the pedestals fill in the level, it uses the water level. Never place the height of a pencil mark, as when pouring concrete, you can paint over it and pour the wrong. Therefore, we use ordinary nails or screws, pre-scoring it at the desired height.

So, as a bump pedestals will go the maximum load to fill their need high-quality concrete, after making reinforcement.

Ideal proportions of concrete: one part cement, two parts sand and three parts gravel. So that the concrete did not sit down quickly, you can add the liquid soap or detergent better. When filling pedestals, they must be carefully provibrirovat that there was no air, it is possible for this use a special vibrator, not everyone of course it is, then you can use a segment fittings. So that the concrete has dried well need about twenty days, but in warm weather on the third day it is already possible to expose the pillars.

How correctly to put the pillars? You should begin with the extreme columns, after which between them have to pull the thread to the correct billing horizon. With the reinforcement pieces can make a template that will be used in masonry to produce perfect and identical seams. It is not advisable to build the right column, as it is possible to build properly.

Each bar is necessary to build poryadovo, check the course you need all levels.

On the second row of each column from top to bottom and must be inserted iron inserts, in order then to them it was possible to weld the shaped tube which is fastened Prof. list. Once the bars have built, it is necessary to proceed to the next stage of construction.

Screwing Prof. sheet. The bars are ready and need to be welded between the profile pipe. "

Grinder cut into the desired size and welded to the metal sticking out earlier with columns. After Prof. tube-set can safely proceed to screwing (outline) prof sheet. Tape measure is necessary Gaugeable desired height and put a pencil mark where the tie is sure to like how you can not get to the professor-pipe and then with Prof. list to do so to speak sieve.

Fill bump between the trenches. Thus, as this portion of the fence no strong load can underpour shallow. Exposed timbering, armiruem and proceed to fill. Once filled, it is also necessary provibrirovat and top atone or zazheleznit concrete.

The fence is already, and you can install the gate and gate. You can buy a wicket, or, you can easily make your own hands, just to include fantasy, or look on the Internet.

Subscribe to the channel, the only way you will be informed of new publications - in front of a lot of new and interesting information!

p.s.: We try to give you the most important, useful information. If you have been interesting and helpful place "like".