Useful content

Budget sliding doors with their hands

click fraud protection

If the choice of material and design of the fence - it is always a compromise between the desire and the ability, at the entrance group - the gate and the gate - to save not accepted. To reduce construction costs, but at the same time get a guaranteed result, Forumhouse users prefer to do everything with their own hands.

Therefore, the focus of this article will be enjoying popularity sliding doors, available in versions for self-repetition, that does not ruin the family budget.

Sliding gates. Option 1

Member of our portal with the nickname max68.2011 I decided to make their own hands sliding doors. Just not the usual, but with upper suspension, and thus to get rid of some of the shortcomings of the conventional sliding gates.

max68.2011 (FORUMHOUSE User):
I have studied a number of topics on our website, as well as familiarize with the offer of manufacturers of industrial sliding gates,with bottom location of the roller trolley. It's not that. I do not like to have to clean the snow, ice and dirt from under the beams under the roller carriage. A standard suspension of sliding doors with upper beam there is a limit on the height of the opening. Exit - to make something of their own, and without overlapping the gate leaf.
instagram viewer

Foundation for standard sliding doors the user has filled in more during the construction phase of the budget of the fence. Initial data:

  • The width of the entrance aperture - approximately 4 m.
  • Depth of the foundation pillars - 1700 mm.
  • The support roller carts - channel "twenty" 2200 mm in length.

Columns:

  • First column - profiled tube 80h40h2 mm.
  • Second column - the carrier, section of 80x80 mm. Welded from 2 mm profiled pipes 80h40.
  • Third column - profiled tube 80h40h2 mm.
  • The fourth pillar - round tube diameter of 76 mm.

Although the foundation for the truck filled with rollers, gates construction was changed to a suspension.

This requires the base - guide beam, on which the "walk" of the carriage rollers.

As a basis for directing max68.2011 I bought rectangular tube 6000h80h40h4.5 mm. Such pipe weighs about 50 kg.

Next, using the "grinder", in the narrow part of the profile over the entire length of the tube pierced by a slot width of 1 cm.

max68.2011 (User FORUMHOUSE):
I beam is fixed on a 4-slot fence poles down. For this, I put it in place and mark places of fixture.

Remember that the accuracy of the production of this unit depends largely on the ease of door travel.

For the manufacture of sliding gates also need welding machine, using which you can learn to read the article Secrets welding for beginners. Because all work is carried out independently, necessary clamps and magnetic squares.

Irreplaceable and angle clamp that allows to record details accurately welded at an angle of 90 degrees.

Welded fittings, the user has fixed the beam on the supports and started manufacturing carriages and gate leaf.

For carriages went perfectly "earring" fixing springs "Gazelle". Metal thickness "earrings" 8 mm, and it has 2 mm diameter holes 17 into which the bolt can be pressed M18. Also required:

  • "Ladder" of the rear spring Zil-131.
  • Two M20 nuts.
  • Bearings - basic and centering.

Svorki for the manufacture of doors and gates are necessary:

  • Shaped tubes (for leaves) - 60h40h2.5 and 40h20h2.5 mm.
  • Shaped tubes (for wickets) - 40h20h2 and 20h20h1.5 mm.

construction assembly was conducted on the timeline and on a makeshift stocks.

It is much more convenient than cooking "on the knee." In addition, significantly increases the quality of work.

Places at the top, where the attached carriage, max68.2011 further strengthened corners 63h63 and 50x50 mm.

sash assembly was carried out with careful monitoring of angles and diagonals, because any misalignment or inaccuracy (ascended from operation to operation) will lead to marriage at the finish.

max68.2011 (User FORUMHOUSE):
Because I work alone, first by putting the details, just grab them and making sure that everything is fine, finally scald.

To enhance the gate leaf is welded jib further stiffening the structure.

Adding jib, mentally imagine as a distributed load of construction. Or, alternatively, you can assemble the model frame gate wings made of wire and to estimate the distribution of the main acting forces.

The manufacturing process of the carriages demonstrate the following pictures.

The bearings are pressed on the axle. After which the parts are stripped welds and the assembly is painted.

max68.2011(User FORUMHOUSE):
After I made the carriage, I tried them in place. Everything moves perfectly. Nowhere does not hurt. Locating bearing is also not required.

The top and bottom part of the carriage covered with rubber covers on the steering rod "Gazelle" and PPC VAZ-2101.

Between the lower plane of the upper horizontal sash frame and the fastening nut studs carriage is placed on the support bearing pin GAS-24. Because side clearances in node low and centering bearings occurs due to the internal angular fillets on the pipe, the carriage moves at an angle.

Having made carriage, hung by the gate, but for the convenience of work left until maintenance support under the flap.

After aligning the guide beam and the gate leaf max68.2011closed fastener sliders with rubber covers.

Finally convinced that everything is working as it should, to the leaf frame welded feigned, making it the strip 40x4 mm.

The user then "stitched" wicket gate leaf and galvanized steel sheets mark C8 and started manufacturing catchers.

To limit the movement of the gate used M10 bolts to put on them with rubber bushings.

Also, the user of a metal plate thickness of 6 mm made roller guide for gates.

With this structure, the roller 4 apply. Additionally required:

  • "Seventy-five" area with a welded ear.
  • Castors 3 cm in diameter with a central hole, rassverlonnym M8 bolt.
  • M10 - 2 pcs.
  • Spring washers (Grover).
  • Bolts and nuts M8 - 4 pieces.
  • Bushings and washers.

The system works as follows: when fully closed the gate bump on the lower catcher, and with the full opening - on the bracket of the guide rollers.

Sliding doors: Version 2

Now consider the budget option "eternal" sliding gate with six attachment points.

hart77 (FORUMHOUSE User):
I chose this option because narrow road to the house, next to the entrance to the site is a column and put the swing gate is simply nowhere. Sliding doors made of those pipes that were scattered in the area.

As can be seen from the figure, the system works on the principle of "simpler is safer", which is confirmed by long-term use of the practice. The design applied homemade rollers which vytochili on a lathe.

Bearings are inserted into the roller vnatyag, whereupon assembly mounted on a "finger" welded to the posts. The rollers are fixed with screws.

hart77 (User FORUMHOUSE):
The system is simple and reliable. Ice, snow is not required to clean rain just do not stay on the tube. It provides all-weather capability and reliability of the mechanism.

Goal for several years. It works like a clock. In some places there was only rust. Nothing never sagged. I saw a similar structure to operate successfully, which is 30 years old.

Note: the repetition of this construction the tube take a larger diameter than the width of the roller. Otherwise profiled, screwed to the pipe, will touch roller.
Note: the repetition of this construction the tube take a larger diameter than the width of the roller. Otherwise profiled, screwed to the pipe, will touch roller.

The design turned out to be so successful and accessible to repeat that many users want to get a similar sliding gates. For example, here is a gate diagram of a portal user with the nickname Kostya11.

And this is the gate of mibo1.

mibo1 (User FORUMHOUSE):
I myself also made sliding doors, working on the principle described above. Sheathe steel sheets have not had time. The tube is picked up, after making the calculation of strength.

To produce the target party portal used 76mm diameter pipe and a wall thickness of 3.5 mm. Width "pure" entry - 4.6 m + gate. Total:.. 5.6 m distance between the supports - 2.1 m Lintel - a pipe diameter 57 mm, wall thickness 3 mm are every 1.4 m 2 row roller bearings operate in.. At the user's words, the gates open very easily.

mibo1 (User FORUMHOUSE):
Door weight influences the choice of bearings. Double row bearings have a huge stock of dynamic and static load-bearing capacity. According to calculations, the weight of my gate - 152 kg. Bearings can withstand the force 212 kg per load point. It turns more than 5-fold margin of safety.

To supporting pillars have a square tube, "weave" 10x10 cm. wall thickness - 4 mm. Concreted pipe to a depth of 0.7-0.8 m, in concrete chippers entry through the ditch. deflector Length - 2700 mm. Height - 1200 mm. Width - 300 mm.

Supporting columns are connected to each other vertically, and diagonally - jib, for which was used a pipe diameter of 76 mm with a wall thickness of 3.5 mm. Welded bottom corner 40h40h4 mm.

And at the end of the article - another sliding door construction.

Musson (User FORUMHOUSE):
The width of the entrance to the site -.. 4 m 6 m length gates pipe diameter of 57 mm was used for carcass flaps. I enclose a sketch of a roller, which I further developed. Instead of the usual curly put the washer, and the second bearing is placed outside.

The topics on FORUMHOUSE described, how to make a sliding gate with upper suspension, and how to build the most reliable and cost Sliding doors with their hands.

We recommend to read the article, which describes in detail, how to make the fence edging board, how to calculate wind loads acting on the fence corrugated steel sheeting. In addition, the website has detailed instructions on Construction of the cheapest fence 1 day.

And in our video scripts showing what fence mesh facadeAnd how to make fence in the style of ancient architecture.

Discuss the article and read other materials devoted to country life you can on the websiteFORUMHOUSE.

Subscribe to the channel so as not to miss the next release!

Snow trimmer attachments for petrol trimmer

Snow trimmer attachments for petrol trimmer

There are many offers on sale for mechanized snow clearing and clearing. These are mainly units b...

Read More

How to prune carrots to prevent sprouting. My grandfather also taught (for which, thanks to him)

How to prune carrots to prevent sprouting. My grandfather also taught (for which, thanks to him)

Fiery fireworks, fellow gardeners!Want to keep your carrot harvest in good shape? Take care of th...

Read More

Instagram story viewer