Flagstaff: his gift, to the envy of neighbors
How to make a flagpole on a suburban area, a height of 10 m: constructive way to install
Flagstaff - a rare visitor in the suburban area. After all, we have not decided to hang out in front of a private home State flag of the Russian Federation. But things are changing. If you want to make yourself or your friends a special gift on May 9, or Day of the Navy, then, from this article, you will learn how to make their own hands flagpole.
Content:
- Homemade flagpole height of 10 m from the steel pipe
- How to install a flagpole in the country site
- Mounting the flagpole on the wall
- Is it possible to raise the flag in front of the house
Flagstaff: step by step instructions on making
demidrol
user FORUMHOUSE
I have a friend. I decided to do it for an anniversary present - to establish ten-meter flagpole. Each will raise the flag of the Russian Navy. From me - installation. Since it - material. And we agreed to.
To make the flagpole, bought in the construction market:
- steel pipes 79 mm in diameter, with wall thickness 3.5 mm, length 6000 mm - 2 pcs .;
- screw pile diameter 89 mm, length 2000 mm - 1 pc .;
- white paint for metal.
The process of manufacturing the flagpole divided into a series of sequential steps:
- On one longitudinal pipe made propyl grinder 50 cm long.
- We cut this piece.
- The result was a paste in a tube.
- In each of the pipes 6 have drilled holes.
- Hammered into the pipe insert and the insert through hole brewed.
- Planted on a second liner tube. Between the pipes leaving a gap of 3-4 mm. The insert also welded to the tube through the holes.
- Circumferentially butt weld penetration.
- Smoothed welds grinder with polishing wheels.
- The pipe screwed and then welded shut eyebolt.
- Drill holes for the "legs" Knecht. Bollard installed and welded to its pipe.
- Painted flagpole.
Setting the height of the flagpole 10 m
How to manually lift the ten-steel "mast"? First - you need assistants. second - Observe safety! Third - follow the instructions below:
- Screw the screw pile into the ground.
- Cut pile of excess metal. Drill 4 holes. Weld the 4 nuts.
- Put the lower end of the flagpole to the pile. Make a small indentation in front of the pile to the lower end of the flagpole. To flagpole has not left when climbing ahead to slide the shovel.
- In the middle of the flagpole, where the weld, tie four long ropes. Immediately pull the two ropes to get an isosceles triangle. Thus, the flagpole, with the rise, will not go neither left nor right.
Now, the crucial moment!
- Pre-insert the eye bolt rope to lift the flag, otherwise then have to climb to the "mast".
- Pull the rope. Pick up the flagpole and substitute for it the first wooden plank with a soft-focus "knob".
- Raise the flagpole above, substituting all one-board and a second abutments.
demidrol
Raise the flag pole, step by step. Up to 45 degrees to lift heavy after - easier.
So, the flagpole stands upright, in a recess near the pile. Fall he will not let four taut ropes.
- Now, the three of us, just lift up the flagpole, and then miss it in the pile.
- Disconnect the rope and fix the flagpole from below by screwing bolts.
Flagpole ready. The flag is raised.
One more photo.
Grandfather with his grandson, raised the flag of the Navy of Russia.
Installing the flagpole on the wall of a country house
And this is another version of the flagpole, is already in the house.
Steelman
user FORUMHOUSE
Flagpole I built based on makeshift, it becomes unnecessary antenna made of steel pipe. In the store I bought two sets. Roll diameter of 120 mm. Put a climbing rope 12 mm in diameter, but advise use ordinary steel, with a diameter of 6 mm, it can not be withdrawn. Also I bought two carbines, to fasten the flag. Carbines fixed on a rope ties. Blocks welded top and bottom. I pulled the rope. Hung flag.
Is it possible to raise the flag on a country site
Questions answered by the portal user LGO.
LGO
Member FORUMHOUSE
Federal Constitutional Law of December 25, 2000 N 1-FKZ "On the State Flag of the Russian Federation" has been changed. His complemented by Article 9.1 as follows:
"Article 9.1. The official use of the Russian Federation National Flag is carried out in cases and in accordance with the procedure established by this Federal Constitutional Law.
"You can use the State Flag of the Russian Federation, including its image, citizens, public associations, enterprises, institutions and organizations in other cases where such use is not a mockery of the State flag of the Russian Federation. ".
Output:flag can be hung on a flagpole and raise over a country house.
On the topic of manufacturing homemade recommend the article:
- Mini smithy with his own hands: the best budget options forge and anvil from the old rails.
- Self-made machines and accessories: Completion garden wheelbarrows, making the budget table for a circular saw, a cyclone from the vacuum cleaner and the frame for fixing the grinders.
- Welding works. Tricks of the trade - nuances and features of manual arc welding: The choice of welding to the inverter characteristics welding different metals.
In the video - Master-class on making forged vines.
And you want to imagine the flagpole?
Subscribe to the channel to join FORUMHOUSE, The most popular portal about building and living on their own land!