Fence edging board. With his hands.

The fence is needed by all. Someone - just isolate themselves from prying eyes. Someone wants to emphasize its status as a fence. Others want to do something original with their own hands. It belongs to the third category of the user with the nickname FORUMHOUSE Dembelek2007, decided to build their own fence edging board. His practical experience, as well as all stages of the construction of the fence will be discussed in this material.

Getting started

The history of the construction of the fence began with the purchase of land. One of the requirements that guided forumchanin when "their land" - to be near the forest, the river and wildlife.

The result of active search was the purchase of land next to a pond and forest. It was then that Dembelek2007 the idea that the fence should be possible to blend in with the surrounding landscape. While in the head "cooked" various options for everything fence forumchanin decided not to waste time in vain and started clearing the site.

Dembelek2007 (User FOUMHOUSE)

I had cut all the grass, clean the area of ​​debris and anthills. Lined tractor small mound on the border with the road.

Thus preparing "foothold" for future work forumchanin Grechischev suitable for this type of sampling.

Dembelek2007

My site is called, "I went in the winter," and I had the time to properly prepare for the construction. I reviewed a lot of pictures with original fences collected at our site. Most of all I liked the fence edging board, built a member of our forum - Spartak. Design work and budget fairly. Based on this sampling, I decided to repeat, with some changes and improvements.

Not surprisingly, forumchanin stopped on this design. Just look at the picture, which depicts a fence SpartacusTo understand the reason for the popularity of the fence edging board.

Of course, make a fence made of profiled sheet is easier and faster than wood, but it is shown by the texture of wood fence gives a spectacular appearance.

Stages of construction of a fence unedged board

Calculation of the number and the purchase of necessary materials

length of the perimeter, which is needed to fence the fence is 120 meters. On this basis, the following materials were purchased:

• Cutting board, which was subsequently treated with antiseptic - 150h25 mm - 2 cubic meters
• On the web intake went unedged board (such boards obtained by sawing the primary barrel wood, hence uneven raw edges with bark), a width of 20 cm to 35 cm and a thickness of 2.5 - 6 cbm
• Pole was acquired by square tubes of 6x4 cm.
• Pillars of the entrance groups have a maximum load, holding on itself Gates. Therefore profiled tube used here 6x6 cm, with a wall thickness of 2 mm and a round 85 mm diameter pipe, wall thickness - 4.5 mm.
• Material gate - this square tube 4x4 cm and 45x45 mm area.

Homemade Gates forumchanin also decided to sheathe the board, and the pillars of the entrance area in the future impose a hyper-pressed brick with the texture of a "wild stone".

As for the construction of the fence required:

• gravel;
• ASG;
• sand;
• cement.

Preparatory stage

Because as the blade is used for fence edging board, not steel sheet, then it before you use, it is necessary to properly prepare.

Dembelek2007

The preparation of edging boards took me all winter, because boards need to be cleared from the wane and pare.

For ease of stripping bark forumchanin produced a special device that allowed the lock board by putting it on the edge.

To remove the bark was used homemade scraper

As a result, I had planed on both sides of the electric planers around 7 cubic meters of boards is approximately 560 pieces.

In parallel with the preparation of boards forumchanin welded metal frame for doors and gates. The dimensions of the gate and gate:

• door height - 2 m;
• scope of one leaf - 1.8 m;
• entrance aperture width - 3.6 m;
• the height of the gate - 2 m;
• gate width - 0.9 meters.

Construction of the fence

After the preparatory stage of transition to the construction of the fence. This is done so - at first mark up the border area and on the four corners We set the extreme polesAnd between them stretch the cord marker. Do not forget to check that the divergence angle between the two sides was 90 degrees, which can use the rule: 3+4=5.

The essence of the rule is as follows: if the measure of one side stretched string 3 meters, and on the other - 4, then at an angle of 90 degrees to the diagonal between them should be 5 meters.

Also remeasure and compare the diagonal, the width and the length of all sides of the fence of the future. If not keep the right angle or not synchronize all quantities, the side of the fence can not be parallel to each other or may get parallelogram. Fence posts Dembelek2007 installed in advance proburonnye homemade horticultural drill hole depth of 1.1 m length of drill -. 1.3 m, blade diameter - 15 cm.

To minimize the forces of frost heaving, which can push from the ground poles, forumchanin not become their fully concrete, and has applied this technique:

• The lower end of the fence posts, perpendicular to each other, are welded two short of the pin fittings. These pins are "anchor".
• The hole is filled with gravel proburonnuyu fractions 20-40. Bedding layer - 10 cm.
• Then in a pit set fence posts. Next concreted lower part of the fence posts. Concrete layer - 25-30 cm. Reinforcing rods - "anchor" - should be in the concrete.
• A pillar is aligned by level, and the remaining space is filled with gravel and CBC fractions 20-40, with careful layering rammer. Filling ramming scrap can be blunt end.

Thanks to this technique - backfilling and concrete "anchor", we get a semblance of a foundation TISE, without having to drill a hole with the expansion in its lower part.

Looking ahead, we say that the fence posts, installed by this procedure successfully survived the harsh winter. They were not kicked out and not mowing.

For more details about how to install a fence so that he was not kicked out of the spring, it is told in the article how to build a fence on heaving soils.

Another important thing to which you must pay attention to - the alignment post - column should not delay / ottopyrivat in the direction of the striper lace. Otherwise, due to the summation of the errors, at great length, can "escape" the geometry of a single row of pillars. Therefore, all posts should deviate from a cord around 3-5 mm.

During the installation of fences forumchanin to simplify your task when digging pits, came up with a pattern. The adaptation is done so - to a bar nailed wooden square, the square side equal to the width of the bayonet spade. bar length is selected so that its length plus the distance from the geometric center of the square, equal to the distance between the pillars.

A template is used as follows: the end of the bar rests on the pillar already installed, the opposite end we place to the ground and aligned axially fence via plumb tempered by stretched cord length of one side of the axis fence. Further produce dredging shovel inside a square to a depth of 25-30 cm, and then starting to drill the hole borer garden.

Aboveground height of the fence is 2 m, the vertical length of the board, which closes the metal pillar - 1.9 m.

The horizontal boards are attached to the inside by means of vertical screws. When choosing this method of attachment should pay special attention to the corners. How to make this knot, clearly visible in this photo.

After installation of the fence webs proceed to the arrangement of the input group. Because when opening and closing the gate and swing the gate poles bear an increased load, as base under them a strip foundation is made.

Its construction is shown in the drawing.

The dimensions of the trench:

• length - 5.4 m;
• width - 0.4 meters;
• depth - 0.4 m.

Before pouring the concrete bottom of the trench is lined with a geotextile, then poured into crushed rock layer of 10 cm.

After tamping gravel on top of it is lined with polyethylene film and fit reinforcement cage.

The foundation was poured on the ground level. The mixture was - "samomes' from mixer 160 liters. The proportions of the mixture are:

• 4 dropout buckets;
• a bucket of cement;
• 1.5 buckets gravel fractions 20-40;
• water for consistency.

After a required strength pillars entry group obkladyvayutsya hyperpressed brick, and the whole inner space concreted.

In order to reduce friction in the target loop are enclosed by bearing balls, with the additional lubricant.

Brick, to preserve its appearance and protection from adverse weather conditions, can be treated vlagoottalkivayuschey impregnation.

At the end of construction on the pillars were installed lights. Flashlights fastened on the dowel-nails diameter of 6 mm. electricity supply comes through the wire PVS 3h1.5 conducted inside the column at the stage of laying bricks.

The total cost of this fence was about 85 thousand. rub.

Select the best fence will help you photos of wooden fences. On FORUMHOUSE you will learn how to build their own fence edging boardAnd how to make beautiful wooden fence. Also, be sure to check the subject of how to make wooden gate with a lifetime of 50 years.

This article presents a selection of the most beautiful and unusual fences. Masters "of all trades" would be interested to read the article, which describes how to make the most concrete pole for a fence.

From a movie, you'll learn what fence-style Russian wooden architecture.