Bits for the screwdriver, which should be in every diy

All health, with you again Mikhailovich. I apologize to subscribers, a few days did not write anything, a little unwell. But here today forced myself, because I know that you are waiting for new materials.

Today I do a little review of nozzles for screwdriver, who bought on Ali for a penny. Little things, but it is very necessary for those who are always something does handicraft with their own hands.

I am a lover of all life hacking and fun stuff that can not only speed up the manufacturing process, but also improve the quality of the result. And today, I do the analysis of interesting tips.

Magnetic limit on drill

At least, this thing is positioning itself as a constraint, but in fact this function does not perform.

On the known limiters are clamping screws which secure it is fixed on the drill. And here it is worth just a metal ball, but if the drill bit or a good pin, Taper easily slips on the drill.

But the magnet function it performs really, I apply it to bits that are not magnets.

Another useful to those who have both left hand and when tightening the screw, the bit slips off the screw and begins to dance leaving no traces on the surface of the beautiful))) Yes, it happens very often. So this device greatly reduces the likelihood of coming off bits with a screw.

Nozzle for twisting wires and removal of isolation

Here is a really cool thing and simply has to be in every diy.

Folding the wires parallel to each other and pushes the nozzle as shown in the photo.

Here, it is desirable to rotate at low speed, otherwise it may not have time to remove the insulation and the wire is wound on the nozzle.

That's the way it wraps two outer wires around a central, at the same time removing the insulation.

Similar story with the two wires.

As you can see, packing winds a wire around the other. I'm not an electrician and does not know whether it is possible so to twist and what is the reliability of such a connection. Accomplish your goal in the comments someone in the know.

For the experiment, stuffed into her pack of wires, clean check, as far as the Chinese miracle of endurance.

On the whole, I coped with the task of packing, but does not look.

The final result is. Two or three cores, this nozzle twists perfectly. The large number of living begins kosyachit.

Drill under p'o-t'ai

Usually, if you want to screw the bolt into the pot, I take a large diameter drill bit and make the seat in the thread to the pain sitting flush.

It turns out there are special drills, as shown in the photo.

It performs the same function as does the seat for the cap bolts.

Here is a beautiful crater produced.

Universal nozzle for crackdown

These nozzles have different diameters and are intended for tightening the screws or screws.

How it works can be seen in the photo. When pressed, the metal rods in the nozzle takes the form of a nut.

But we humans are Russian and rarely use things only for their intended purpose. Spinning it possible not only to nuts))

The test results showed that the idea itself is elegant, versatile and very comfortable. But if you decide to buy yourself this, you should choose a reliable manufacturer and do not take the "Chinese". This Chinese nonsense I have not worked for a long time. When screwing in the dense material, packing slips. And if you have a powerful screwdriver and you have not set up the force, it is the Chinese miracle disintegrates into pieces.

Nozzle for metal grinding conically

Here are the products clear. The task of the nozzle to make a cone from a metal rod.

That such effect is obtained. The spring in the country will be sharpened metal bars under the tomatoes, to the best entry in the land. So I check how much it will be enough, because it is also Chinese.

Nozzle for sharpening drills

Here is the thing for sharpening drills a very useful and easy to use was. Of course this is an option for those who like that can really sharpen blunt drill and prolong his life. For specialists in sharpening it certainly is not appropriate.

It stated under what size drill it is made.

The principle of operation is simple. You connect the screwdriver to the nozzle as in the photo.

On weight it is better not to sharpen, not very convenient. Place the tip on the table, insert the drill bit and forth.

Despite the simplicity of the product, even here it is necessary to know the rules of the drill sharpener, at least at the level of the fan.

At this until all. I ordered more batches of different small things Ali, as soon as she arrives, then immediately do obzorchik.

Mikhailovich was with you. All good and peace! Do not be ill!!!

Interesting materials for readers to view:

We do welding holder for placing your own hands

Which drive to use grinders for cutting wood?

Simple lathe wood: step by step guide

How to fix the plug in the wall of the loose? As easy as pie