The dream of a perfect home or how I built BarnHouse. part Four

In the fourth part of the construction of the series: the installation of profile sheets to the roof, facade finishing stages planed board and frame insulation value-shed house 2 million. rubles

Construction series about BarnHouse construction of entering the home stretch. In the previous parts:

• Why FORUMHOUSE participant and architect Eugene Likhachev I decided to build a house, barn
• What are the advantage of the winter construction karkasnika and advantages of precast concrete piles
• As no wage workers put the "box" frame houseAnd what tools are needed for this

From this series, you will learn:

• How to mount a trapezoidal sheet roof of a frame house
• How to decorate the facade of the planed board, and it's better than an imitation of timber
• What layer of insulation laid Walling barn-house

Installation of vapor-permeable diffusion membrane and profile sheets to the roof BarnHouse

During the construction karkasnika often confused where to put a vapor barrier, and where to mount the waterproofing film. Recall:

Vapor barrier is placed inside the warm circuit and vapor permeable vlagovetrozaschita - outside.

If you comply with this recommendation, the water vapor got into the insulation of the house, free to come on street, not condense inside the insulation, leading to a decrease in its thermal insulation characteristics.

 See how Eugene Likhachev came to the unit roof, step by step:

1. On top of the rafters, he spread the diffusion membrane.

This material passes steam but does not allow atmospheric moisture and condensation to get into the insulation.

2. Further filled bar section of 5x5 cm.

The bar forms a ventilation gap to ventilate the roof space.

3. Eugene over the bar mounted lathing of boards section 15h2.5 cm by 15 cm.

4. On crate he laid galvanized steel sheet 0.5 mm thick and 21 mm in wave height.

EvgenLikhachev

An overlap profiled sheet, in two waves. Horse - 20x20 cm. Between the ridge and laid the trapezoidal sheet foam 2x4 cm from the blowing snow.

EvgenLikhachev

Membrane roof with overlaps goes to the wall. To fix the lower part of the front batten between sleepers made insertion of a board section 15H5 see. I'll finish the facade vertically mounted board. To do this, first, filled vertical lathing of boards section 10h2.2 see. Used nails 7 cm long. Then filled a horizontal crate. Used nails 9 cm in length, is guaranteed to be fixed for the frame counter.

Decorating the walls of the barn-house planed board

Wooden facade requires a thoughtful approach. It is one thing - the picture on the internet and quite another thing - a board mounted on the exterior walls in the real world. rule:

First make a 3D visualization. Then mount the board on the test area of ​​the wall. And only then if the results are arranged completely facade trim a tree.

EvgenLikhachev

At first I planned to decorate the facade of the imitation logs. I bought a pack of imitation, width of 18 cm and obbil her a small section of the wall. I looked. Not that. In this article there is no idea BarnHouse - the idea of ​​using simple natural, not factory-materials for the barn at home. The result beat the usual finish planed board with panel strip.

Initial imaging finishing barn facade-house.

Option with the imitation logs.

The final result from pine boards.

On the wall gone board section 20h2.5 see.

Constructive finish:

• The length of the boards in the longitudinal part of the facade - 3000 mm.
• Overhang at the bottom of the purlin, - 100 mm.
• The length of the boards gables - from 3050 to 4000 mm.

• Mounting on galvanized "white" screws 3.5h45 mm.

Boards fastened first "rough", 2 self-tapping screws.

Then, pulling the braid, is screwed on the screw 3 in the crate. It took a total of 18 screws per board.

Total consumption of screws on the wooden facade - 4000 pcs.

After finishing Eugene facade windows installed.

Mounted wind lath size 145h135 mm.

Knot fastening strap wind close-up.

The gap depth of 45 mm by zavedet rail-batten.

All work on the construction of a frame house, barn were winter.

Warming BarnHouse rock wool and installation of a vapor barrier

Recall that Eugene insulate karkasnik as follows:

• walls - 200 mm;
• roof - 250 mm;
• floor - 300 mm.

EvgenLikhachev

House-barn I are thermally insulated with rock wool rolls and slabs. wool Thickness - 100 and 50 mm. Happened:

• Ceiling - 10 + 10 cm wool in rolls and + 5 cm cross minvatnoy insulation plate.
• Walls - 15 cm wool in rolls + 5 cm wool slab.
• Floor - 15 cm wool rolls + is cross 3x5 cm wool slabs.

With the rolls work comfortably. Only between the rafters they are poorly kept. I had to cut across the roll and fasten it with the tapes cut from windscreens. More further laid a skate mauerlat 5 cm and a heater that are not blown joints.

Before you buy insulation, read the manufacturer's recommendations and find out that the heater can be used for installation on sloping and vertical surfaces. Or its scope - insulation only on horizontal surfaces.

Vapor barrier frame walls.

Eugene overlaps glue double sided tape.

You've read the fourth part of the construction of the series "I built BarnHouse ». In the final part:

• Finishing and painting karkasnika
• The closed space between the house and the land in the pile foundation
• heating cost house-barn with electricity by means of inverter air conditioner

You can ask Eugene in the subject line BarnHouse Likhachev.

We recommend an article - karkasnik correct or not build Rushen terrible karkashen.

Want to test knowledge of the frame housing technology - pass a little test.

look,how to build a frame house unusual round shape.

Subscribe to the channel. Share in social networks. Join craftsmen FORUMHOUSE.