Wooden facade with their hands
Any of the owners of country cottage is well aware that the facade, except for home protection from adverse weather conditions, and also performs a decorative function.
The modern market offers a variety of materials for wall decoration: decorative brick, stone, vinyl siding.
Although most developers choose classic options unabated interest in wooden facades.
Ventilated facade made of plywood under the Framework
Bavar (Member FORUMHOUSE):
- For bar-shaped house, I would like to make a facade in the style of "half-timbered". Almost a year I was thinking over the choice of material in the end the choice fell on a water-resistant plywood.
Another argument in favor of this material became the next "experiment". Forumchanin on the site two years spent waterproof plywood scrap that for all this time is not swollen and did not change its geometry.
Bavar:
–For convenience, I picked up the plywood 1220h2440 mm and 9 mm thick. If we compare the OSB and plywood, then, in my opinion, OSB - a delicate matter and, unlike plywood, he easily beat off the corners.
As a heater Bavar used stone vatutolschinoy 100 mm. On board went crate - 40h125. Since, according to the calculations forumchanin walls weight with the facade will be approximately 1.2 tons, it sheathing fastened to the wall for support metal corner 90x90.
It is important to know that without the ventilation air layer wooden house under a hinged facade can rot.
Jury in (Member FORUMHOUSE):
- I have a house from a bar lined with siding, you want something more interesting. I look to the Framework. That's only doubt - bar continuously "breathes", and the house just walking, I am afraid that will lead facade.
To avoid this, between sheets of plywood, leave expansion gap of 3-5 mm.
Bavar(Member FORUMHOUSE):
- At the stage of installation I did not play, because me alone, running on "Forests", it is difficult to move a sheet of plywood. But after plating the walls of a circular saw, I went all the joints, ensuring the expansion joint of 3 mm.
To relieve the tension from the torsion Validating at the joints of boards he made propyl to a depth of 5-7 mm.
To simulate the power frame beams Bavar attached to the facade of a simple edging board size 25h150mm. For 6 months of using the facade of plywood in the style of "half-timbered" showed their best side. For it is easy to care for, and the house with the facade attracts admiring glances.
If one of the members of the forum wants to repeat the work, you can be guided by the following amount. The total facade area - 120 sq.m. On materials out:
- 25h150h6000 board - 48 pcs;
- board 50h200h6000 1 unit;
- plaque on the crate 40h125h6000 - 38 pcs;
- plywood 9 mm, water-resistant, PSF 1120h2440 - 52 sheets;
- insulation 1000h600h100 - 28upakovok, approximately 100 m2;
- facade paint - 30 liters;
- antiseptic - 12litrov;
- corners for fixing lath 90h90h40 - 150 pieces;
- 110h76h40 timber support - 36 pcs;
- Optional: screws, galvanized nails, foam, brushes, rollers.
Total amount - 112,000 rubles. On average, 1 sq.m. this facade has managed Bavaru to 932 rubles.
Sheathe House "American"!
Knotko (Member FORUMHOUSE):
- I want to sheathe House "American." I plan sheathing board 15h125 mm, making overlaps of 20 mm. How to do it yourself?
Mar7ina (Member FORUMHOUSE):
- Boards, size 25h150h6 for this facade we bought a nearby sawmill, but when the order was brought, it became clear that no two identical boards! Walks the thickness, width, or board - wave. I had to take over the plane.
After the new posts obstrugivaniya boards plated their soil-antiseptics and folded in a drying rack.
Mar7ina:
- A total of impregnation took 3 buckets of 10 liters. Sheathing began only in August, by which time the board had already dried up and become noticeably lighter.
Each new posts doskuk bar lath nailed one and ershonnym galvanized nail. As a result, after painting the gray paint of the facade, the house began to look a lot more elegant.
Another interesting approach to the arrangement of the house, "American." To process the boards with a "walk" the size of a user forum with the nickname Spiridonov I bought a woodworking machine.
Spiridonov(Member FORUMHOUSE):
- The purchase of this machine is justified, if the size of the board is greater than 6 m3. There is only one thing... You need a lot of free time, and at least two employees. Because facade area of my house - 210 m2, the machine has justified investment.
Forumchanin calculated that the average processing time rm board 1 is 1.5 minutes.
Total:
- board delivery - 40,000 rubles;
- Machine - 17000 rubles;
- paint / primer - 20000 rubles;
- nails, cutter, brush and so on. -7000 rubles;
- cost per square meter - within 400 rubles.
Spiridonov:
- The most expensive in that the facade - is the elapsed time.
Burnt facade boards
Great interest in the forum is a method for treating wood as firing. In Europe, the USA and Japan, the facade of a material widely spread and applied in the decoration of cheap houses and luxury villas. So what's the advantages and features of the facade, and most importantly - how to do it yourself?
blizzard(Member FORUMHOUSE):
- I have a house built in 1971 lined with burnt edging board, and the texture of the wood still looks great!
When choosing this type of facade is necessary to pay attention to this point.
Chungachanga(Member FORUMHOUSE):
- Contrast the figure obtained by the surface treatment of wood with a blowtorch, quickly weakens under direct sunlight. For example, drawing on the wall cladding house, situated on the sunny side, it loses contrast in a couple of months. Therefore, do not burn the plank wall cladding, which is exposed to direct sunlight.
For baking the most suitable soft pine wood with a pronounced pattern of annual rings - pine, spruce. With regard to change of properties after firing, with the timber there is the same as that during heating in a furnace.
Heat-treated wood is more dense surface.
This reduces its ability to absorb moisture from the air. During heat treatment disintegrate wood sugars, which are breeding grounds for a variety of organisms, wood-destroying. As a result, the tree does not rot.
Vasilevs(Member FORUMHOUSE):
- I live in a wooden house in 1951 the buildings. Lumber outside walls charred. At first I thought that the house was rebuilt after a fire - it turned out that the tree is specially burned for safety and then obbili clapboard.
Usually on the facade of the tree burned gasoline burner, but users of our forum, to accelerating the process, it is recommended to use a gas burner.
Iivan(Member FORUMHOUSE):
- Gas burner not many tried and tested. It is better to take the gas burner, the hose "oxygen" convenient length and gas cylinder 40 liters.
Burn the tree can be up to full black, as they say, "to the coals."
Daniiis(Member FORUMHOUSE):
- I fully obzhog facade of his house a gas burner, and it is - hellish work, but the result is worth it!
Abolin(Member FORUMHOUSE):
- To be effective, sProtecting facade boards need to slowly burn with its surface layer as much as possible. A timber should be, ideally, resinous.
In a typical situation, the firing - a decorative technique with weak preservative effect.
For fast processing of wood that goes to the front, you must use antiseptic substances.
To preserve the color after heat treatment even burnt subsidiary timber must be covered with varnish or impregnated.
facade ventilation
When the device of wooden facades are often the question arises: whether aerial is needed and windproof membrane layer? Let us turn to the members of the forum experience.
Nicola(Member FORUMHOUSE):
- I am a lumber house plans to warm mineral plate, then sheathe clapboard. Whether it is necessary to leave the ventilated gap between the insulation and paneling, and whether it is necessary to put windproof membrane?
sys81(Member FORUMHOUSE):
- The gap is needed, so thanks to him for water will not "stand" and slide on a heater or evaporate under the influence of rising air, which will go from the bottom up on a ventilated gap...
According to forumchanin with the nickname jtdesign,the right wall of the cake with a ventilated facade is as follows:
- clapboard siding goes on the crate, and not directly on the frame;
- kontrobreshotka placed horizontally or vertically;
- kontrobreshotku fill insulation, then carefully put vetrobarer;
- further mount facade material.
Detailed and vivid story forumchanin to erect half-timbered facade available here. Hot discussion burnt facade board is conducted in this topic.
How to sheathe House "American"? The answer users forumhouse.ru can learn here. All information about ventilated facades assembled in this topic. How to sheathe House edging board, you read here.
In that video It explains the nuances of the construction of a frame house with half-timbered facade. And the most common errors in the construction of a country house, disassembled in this video.
Discuss the article and read other materials devoted to country life you can on the websiteFORUMHOUSE.
Subscribe to the channel so as not to miss the next release!