We frosts are not a barrier: inclosure and build winter

Modern technology makes it possible to use for construction is not only the warm season. If you use a special cover, and winter suit

Well, when everything is going according to plan and have the energy, time and money to enter the winter with the finished construction. However, do not always work out as planned, the construction of an object is sometimes necessary to begin or end in the cold. It is more difficult due to freezing temperatures, but in reality, if we use special technology - inclosure. Members Forumhouse, faced with winter construction, actively apply Tepljakov and recommend them to everyone caught cold in the midst of the process.

Content:

• What is the overall housing
• Why do I need to warm
• Real experience winter concreting

That the "beast" inclosure

Inclosure - vremyanka erected around the construction site to maintain the inside of the positive temperature.

This can be the similarity of the tent stretched over after pouring the foundation. And sometimes - and a huge tent on the perimeter of the object, when it comes to insulation and decoration of the facade. The insulation material used is a film - usually reinforced, shrink, and canvas or PVC tarpaulins. To frame used wooden beams, are knocking together the pillars on which is stretched insulator. To minimize heat outflow solder film in a single web by building irons or burners.

Tepljakov inside temperature is maintained by thermal guns run on electricity, diesel or gas, depending on the communication available on the site.

Why do I need to warm

Using Tepljakov lets in the cold season to perform various construction manipulation. Most often they are used in the following wet processes.

• Pouring the foundation - belt or tiled.
• Pouring floors.
• Facade insulation - foam, Epps, mineral wool and similar materials.
• Wet exterior decoration - a variety of plaster on the basis of cement.

Clutched to the solution gradually, reaching a grade strength, it should reach after casting at temperatures above zero. Even cold-resistant supplements are no substitute for the heat, they just speed up the process. If the solution freeze fluid, the foundation spring starts to crack and flake off. This may not happen immediately, but the life of this Frostbitten base considerably lower than projected. A redo the foundation for a residential home - the process expensive in every sense.

When it comes to be poured in cold weather, inclosure protection of concrete and give it to stand.

Real experience winter concreting

Teplyakov positive experience use when casting basement divisible AlexeySB3.

AlexeySB3

Member FORUMHOUSE

Casting began on 4 January in the cold, concrete, walking with the addition of up to minus ten. Zalilis for dinner, immediately began pounding inclosure and stretch material. By seven in the evening inclosure I was ready, started a couple of cannons ten kilowatts - gas, with a fan. From 4 to 8 January changed cylinders. The temperature inside, when the street minus seven, remained at plus six. When the frost hit at minus twenty-six, into the plant stayed, plus one. The foundation has hardened properly, nothing is frozen and will not crack.

That forumchanin azemskov not afraid frosts and proceeded to fill overlap.

azemskov

Member FORUMHOUSE

Concrete supplying warm, with addition of minus five, fill took about two hours. Another half-hour film hid the plate and pulled the top inclosure. Including three diesel guns, total power - 80 kW. Hot-air inflated tent, turned the dome, no additional supports are not set.

Heat requirement also applies to the other wet processes. heater plates mounted on the first adhesive mixture, and after solidification fasteners supplemented plastic dowels. As is the case with the concrete, the adhesive should harden at a positive temperature.

After facade insulation layer reinforced with glass fiber mesh, again using the adhesive mixture and warm. When the reinforcing layer has dried, it is applied to the decorative plaster. A spring to this beauty not crumbled, the temperature during finishing and drying should be not less than five heat.

And to work with the solution in the cold - sheer torture or layer does not normally cause nor beautiful drawing is not achieved. Into the plant the gun needed to catch up work and drying degrees. As in the case of the foundation from frost additives do not save. This is confirmed by experienced fasadniki involved in the discussion of the theme, for example, ikgstroi.

Ikgstroi

Member FORUMHOUSE

I am also against supplements, if it is fundamentally the customer does not want to postpone the insulation and decoration of facades until the spring, we put Tepljakov. Work is already not the first year, all the objects on the guarantee, no complaints.

Dimensions Tepljakov depend on the variety, for the foundation enough stocky frame. A facade build a kind of a cocoon around the perimeter of the building or in parts. In this case, the overall housing combined with the forests that shelter did not stop working.

Suitable inclosure and for the erection of structures on permanent formwork technology. The main thing is to ensure the "plus" the first few days. Once the water is fully react with the cement, frosts are not terrible. Monolith, flooded in winter, in the spring of gaining maximum strength.

Output

Due Tepljakov, if necessary, can be built in the winter. Patch makes it possible to observe the technology and get a quality foundation, floor or facade.

An interesting way to do without formwork - pour tape straight into the ground. Modern energy-efficient foundation is UWB. In the video - winter concreting into the plant.

Subscribe to the channel! Share on social networks! Join FORUMHOUSE!