Building a brick warehouse annexe: fotoinstruktsiya

User portal tells how he self-built barn for storing boards, ladders, garden wheelbarrows and sacks of sawdust on frame technology

Sometimes it is better to see once, than hundred times to read. Therefore, in this article, a minimum of words and a maximum of photos of how the participant with the nickname FORUMHOUSE sashauzer, erected a warehouse for storage of lumber by hand.

Content:

• Start of construction of a warehouse
• How to build a low-cost foundation for a barn
• How to make the sill frame hozbloka
• How to self-assemble the frame of the boards of the barn
• How to make a wooden beam on frame technology
• How to raise the wall and do not overstrain karkasnika
• How to make the roof of the shed and cover it with a bituminous corrugated sheets
• How beautifully sheathe the timber framework imitation
• How to make easy storage for lumber
• The results of the operation of a warehouse and life hacking
• Video, where all the stages of construction of the frame of the shed are shown in detail

Why build a warehouse for the storage of boards

Cabins, sheds, hozblok. These buildings are always needed in the suburban area. Our portal has repeatedly talked about the different home-made "saraykah» FORUMHOUSE users. We offer another version issued in the form fotoinstruktsii for construction. Explore our stuff, and then you can build a frame that's a warehouse in the Finnish style.

sashauzer

Member FORUMHOUSE

Boards, cutting lumber, goats and other household items - a perennial problem in any country site. They clutter the area. Their awkward to store on the street, zastilaya film and crushing it with bricks. All boards are not zakinesh the workshop. In general, I decided I needed a warehouse for storage of lumber. Size structure 2300h4000 mm. In it quietly placed planks up to 3500 mm in length and still remains a place for all sorts of goodies. For convenience, the aperture is made to 3000 mm wide. I hope my experience will be useful to users of the portal.

All stages of work the user has broken into a series of sequential steps.

1. Building the foundation

At first sashauzer I removed the mast from the liner of electricity, and skin from the side wall cabins, workshop, to which he has decided to attach the boards to the warehouse.

Rate the building site where once stood the street vanity.

The basis of the foundation of additional building - concrete blocks of 25h18h40 see.

Blocks placed on the gravel with screenings and broken bricks. The upper part of missed blocks and further bituminous mastic adhered thereto roofing material.

horizontal blocks, a user has exposed using a spirit level and smooth wooden block.

Also blocks additionally reinforced edge portion to the ditch.

Along the way, sashauzer I bought the board for the construction of the frame and roofing material.

2. Manufacturing of the carcass Strapping

Tying - board section 20X5 cm, which knocked off the supports for the lag - board 10x5 cm.

All boards are treated with antiseptic toning mahogany.

Laghi - board section 15h4 cm.

To lags were not above piping, they sawed grooves.

For precise sawing boards to mark up the place with a pencil.

Tying shot down using neyler.

Leveled structure and verified diagonal.

Step lag - 65 cm.

Next, the user planed carpeted floor board section 15h4 cm.

Boards nailed Pneumatic hammers, nails 9 cm in length.

To accurately to drive nails into a log sashauzer, a guide, pulled the lace.

 Boards are also processed bioshield composition.

3. frame assembly warehouse for storage of lumber

Warehouse wall made of planed boards section 15h4 cm. Sawed rack on the circular saw.

User started to collect frame with manufacturing side of the wall, which follows the slope of the roof.

Further, it has collected a rear wall of the frame store.

Step racks - 1 m.

Gash under jib made by all the rules karkasostroeniya.

According to sashauzer, the most interesting part of the frame - a front wall with an aperture of 3000 mm. The user decided to experiment. He made no bolt of boards set on edge and box-fashioned wooden beam, its sheathing sheets SIR thickness of 9 mm.

The manufacturing process of the board crossbar 10x4 cm:

• The user cut to size sheets SIR.
• Struck a wooden frame adhesive foam.
• He knocked foam trowel to make a thick mass.
• SIR cleaned from dust and surface sheets moistened with a damp cloth.
• OSB neylerom nailed with nails in step 6 cm.

General view of the wooden beams.

Pre-calculated beam strength in a specialized internet calculator.

4. Independent lifting frame wall

Sashauzer I put up a wall frame warehouse together with my mother.

For insurance, the user took the rope and gradually slipping boards of different lengths, the wall rises above.

sidewall sashauzer I picked up one.

I leveled it on a level with the help of the spacer bar, fix mowing, as well as all the walls between them.

5. Manufacturing shed roof-karkasnika and assembling roofing

Shed roof rafters made of boards section 10x5 cm.

At the lower and upper ends of sawn seating for a snug fit to the upper piping.

Flooring - board "dyuymovka".

Top paved wavy bituminous sheet.

sashauzer

When I closed the nail heads on the bitumen corrugated roof, it turned out that they were very tight nalezayut. A hammer to drive - not an option. Split. I found a solution - heated building their hairdryer, and they are easy to snap.

6. Facade karkasnika of boards and timber imitation

The side wall of the warehouse user sheathed timber imitation, he dismantled the wall hozbloka.

The back wall, to save budget, trimmed planed "dyuymovka".

front wall sashauzer CAP also sewed and decorated the imitation logs.

On the wall was gone only one pack of imitation logs.

Place additional building compounds with enhanced hozblok galvanized metal strip 1 mm thick.

Binder made of lining overhang.

Cornice board made of planed "dyuymovka", width of 15 cm and is fastened to the galvanized screws.

Overhang painted with white paint to contrast.

Joints linings closed imitation false-beams in the form of removal of the rafters.

7. Original storage system boards in the shed

To stock building materials or cabins have always been the procedure, and you do not have to constantly look for something, you need a storage system. Sashauzer It made the original storage for wood. Now every bar or board are in place and easily accessible.

sashauzer

Of course, you could buy a metal rack, but I'm not looking for easy ways. Therefore, a system consists of what is at hand. The idea is simple - to boards, see section 15h2 attached bars section of 4x2 cm. Structure fastened to the frame uprights. Turned grooves for open shelving. They put in oak bars 45 cm long, which put the board.

The steps of manufacturing the rack:

• User glued bars on the mounting foam and nailed their nails.

• Excess foam immediately removed with a chisel, so that they do not fall into the slots.

• The ends sanded.

Total sashauzer fashioned 5 poles - 3 pieces. for long wall and 2 pcs. for the end of the warehouse.

In each support 17 is made of grooves.

Storage system boards assembled.

Details are screwed on the screws length 7.5 cm.

An interesting nuance - vodostochka made of plastic pipe, and not to buy expensive funnel and transitions, the user flexed them himself, using a hairdryer to heat the building.

Also held at the warehouse lighting.

The general form of the frame for storage shed boards and housewares.

Useful advice on using the warehouse

Warehouse sashauzer participants liked FORUMHOUSE. On the user's questions fell.

e1g1o

Where an open doorway, gate will?

sashauzer

While I only pulled reinforced film with a weighting agent. When you need to curl up and matured on hooks from the ceiling of the warehouse. Then I plan to make a tent, which will be wound on a roll as roller blinds.

avamonster

Warehouse excellent! But I understand that the boards and the money spent on this building several times larger than the value that is stored inside?

sashauzer

Yes, the money is spent more than is stored in the form of boards. But the board is - consumables and storage easier to work in the studio. It reduces the time to find the right piece of wood. It allows you to store different relevance and usefulness. If the rain comes, it is a place where you can collect anything. And still adorns the building site.

And lastly, a small life hacking - user keeps the ladder from the ceiling, securing it on hangers made of shaped tube section 2x4 cm and strapped them pieces of old bicycle camera.

The staircase is always at hand, and takes almost no useful place in a warehouse.

conclusions

FORUMHOUSE introduced you to a job well done. We are sure if you want, everyone will be able to repeat the design sashauzer, or use some elements and parts for their buildings.

Those who want to get acquainted with all stages of user experience, offer them look shot video.

You can also ask a question to the author in his subject - Warehouse timber Workshop Storage.

We recommend to read the article:

• How to turn pozhivshuyu shed in a stylish and comfortable guest house: Reconstruction, inzhenerki, operation.
• Renovation of cabins female handsFrom the frame to the exterior trim.
• How to lift and move the shed if there is no crane and manipulatorBut it has a direct hand winch and jack.

In the video - Mini house from cabins with their own hands: The appetite comes with eating time.

Subscribe to the channel! Share on social networks! join FORUMHOUSE!