The liquid tube: finish for interior and facade. real experience

What is a liquid tube, the scope of application, the application of technology, experience of the participants of the portal

Stopper - sufficiently hot interior finishing material for almost all types of surfaces: walls, floors and ceilings, even, if desired. However, only recently it appeared on the basis of finishing cork, designed not only for domestic but also for outdoor applications, and virtually any reason. Decades of experience in the application of the coating in our country there, but some results are available. The market is presented and imports, and domestic producers have to choose from what, the price - in other facade systems, so it is worth considering the liquid plug closely.

Content

• What is liquid tube
• Scope
• application technology

What is liquid tube

The liquid, it also is sprayed plug - universal finishing material consisting of balsa wood chips, the fraction of 0.5-1.0 mm and a polymeric binder with builders and water. Essentially - a good example of the use of waste products, as the main component is obtained during the manufacture of various cork. Turn waste into profit guessed Spaniards, the first liquid stopper appeared in this country in the early two thousandth. Domestic producers have offered an alternative to import about 2011.

This material is a homogeneous mass, which after curing forms on the surface of the moisture resistant, vapor permeable, elastic covering visually resembles Kameshkovo plaster.

Due to the general basic component - cork, products of various grades has similar basic characteristics:

• High decorative - an interesting texture, visually reminiscent of cement "coat", a large range of colors;
• high adhesion to various substrates - concrete, brick, wood, metal, FCL, DSPs, GSP, OSB, particle board, PVC, PPS, ceramic tile, glass, cement, plaster and others.
• high elasticity - withstands base shifts without formation of cracks (and the tensile elongation of about 33%);
• water vapor transmission rate - through the porous structure itself cork and the ability to pass air polymer binder (up to 75%);
• moisture - vapor passes without drawing water into the inner base layers.

In addition, all manufacturers are positioning their coverage as a heat-insulating and sound-insulating material. Yes plug has similar properties, but all depends on the layer thickness. On average, it is recommended to spray façade 4 mm in some approaches, the thermal conductivity, they will be equal to 4 mm PPP. Of course, talking about the full insulation in such a situation is not necessary. However, due to impermeable cork without cold bridges comfortable in the room will be unique.

As for insulation, then again, it all depends on the layer that had a real effect, the base 4 mm is obviously not enough, and do more inappropriate. Cork sprayed plaster - a real alternative to the ventilated facades and wet facades, but if necessary to increase the heat-saving parameters, then it must be applied on top of the thermal insulation materials.

That is - a finishing protective and decorative coating, but to completely replace the insulation, as well as sound insulator, it can not.

As for durability, the test of time has not passed yet, due to the "youth" of the technology itself and the relatively short period of use in our climatic conditions. But indirect factors can be assumed that the producer declares life of 10-15 years are very real.

Kotiara82

Member FORUMHOUSE

The basis liquid tube - and acryl crumb cork oak. Acrylic has long lived in our area, it is made, and the primer, and vodoemulsionku, added to the adhesives, and so on. N. And the greater the proportion of acrylic in the composition of these products, the more they are high quality. Acrylics provide shelf-life of about 10-15 years, cork is also quite durable, especially acrylic covered thereby. Everything else - modifiers that improve starting properties. So it is necessary here to dance on the acrylic. As for the practice - STS-plated pieces were lying on the street in the rain, sun, snow 2.5 years - of course, get dirty, on the ground is littered, but no significant changes can be seen.

Scope liquid tube

Judging by the manufacturer's website, then it is almost a panacea - waterproofing, thermal insulation, protection of any reason from outside influences, giving a presentable appearance. As for insulation, waterproofing, there are highly specialized materials, and this is clearly not the cork plaster.

As for protection against external influences, it is a reality - it protects against waterlogging, which is especially important for timber and different plates based on wood waste.

Due to the textured surface of the wall may become contaminated, but if done blind area and the water drainage system, this does not happen, and façade long retain decorative. Paints based on acrylic are considered to be resistant to UV light, thus burn liquid plaster even in full color, too, should not, and if you choose the pastel range, the problem and does not will be.

The material for interior and exterior use on vertical and horizontal surfaces of any geometry. It is used not only for the walls in the rooms and on the facades, but also on the facades and roofs. However, if you plan to use on the metal base, or when the walls contain metal inclusions (Permanent formwork from schepotsementnyh plates) of the liquid tube must include a corrosion inhibitor, most often zinc phosphate.

In recent years, cork is becoming more common with the facades of houses from SIP. Due to the high elasticity of the plaster can be sprayed directly on the plate, without damping layer (PPP, rockwool), as is the case with wet facades. It is suitable for the restoration of the lost form of reason - looks interesting by brick, by log cabins of logs.

Tan301

Member FORUMHOUSE

Three years ago (2014) blew - in the seams of the cork sealer outside tube.

application technology

As with any other topcoat, is applied to the liquid stopper solid, purified from pollutants and dust bases pretreated with a primer. The seams at the joints of panels necessarily thicker than 2-3 mm are terminated with acrylic or cork same sealant as seams between the logs in the log cabins. Before applying the cork surface and all neighboring facade elements necessary to protect the film. Otherwise, remove the plaster from tides, drainage system and any other surfaces will be very problematic.

sparks333

Member FORUMHOUSE

I did the domestic liquid stopper of permanent shuttering of schepobetona. Coated happy, but it is bad that the entire blind area soiled and window sills are not laundered. Film badly covered up.

Material is delivered ready-to-eat - natural color or with the addition of caramel and viscous consistency.

For prolonged storage may need the addition of a small amount of water, preferably distilled or filtered.

Prior to use, the mass is thoroughly mixed with a mixer or a special attachment on a drill / punch, at medium speed for a few minutes.

The liquid plug is also called sprayed, since it is applied on the substrate by spraying under pressure through a special equipment - kartushnogo gun.

Apply the plaster in several layers, with an interval. Some brands, especially foreign ones, allow deposition of the next layer after a few hours, but in our climate do not necessary, except under certain conditions.

fokis

Member FORUMHOUSE

For our band, in my experience I advise you to wait at least a day. Two layers of the day, I also apply, but then it was the heat. So in fact, I can tell you that the layer - day.

Manufacturers and dealers usually offer services in drawing, but actually do on their own if desired.

Vladimr

Member FORUMHOUSE

Despite the fact that the first time I was holding a gun kartushny, not bad, in my opinion. The purpose of the experiment was to show their skills in the application of plaster, and to try out the material. Apply it yourself can be, nothing complicated. My main problem was to "fill the hand" when driving stucco gun, but missed a bucket of material through the gun, you begin to understand how to properly manage it. Especially in the network weight training videos.

Vladimr I inflicted on the stopper plywood base, in which case the manufacturers recommend a first layer do minimal thickness - 0.5-1.0 mm to plywood not swollen. The same rule also works when applied to the GCR or gypsum fiber board with interior use. In other cases, usually two layers, each about 2 mm thick - the second and first overlaps flaws visually aligns hue.

To dry completely (up to three days on non-porous substrates) coating is susceptible to moisture, to work on the facade on a rainy day is not recommended. After complete drying of the plaster is resistant to all kinds of weather, and mechanical damage it is problematic enough.

Output

The liquid tube - one option or the restored new trim facades from different materials, which is characterized by sufficiently high performance and decorative characteristics. What prefer depends on the taste perception - not everyone likes the "coat", and the financial capacity - not the most expensive, but not particularly budgetary coverage. However, each product has its own merchant, and a number of fronts, covered with plaster that is gradually increasing.

For those who prefer ventilated facade systems that may be of interest concrete tiles or fiber cement siding. Adherents of wooden facades - material a vertical trim edging board. In the video - new and popular facade materials presented at the international exhibition.

Subscribe to the channel! Join FORUMHOUSE!