Why spark plug and how to eliminate

Here it is a bad moment, you've been paying attention to the power outlet and it is unpleasant gleams when you insert the plug, or just because. No need to immediately run to the phone and call an electrician friend, it is likely the cause of quite petty and you handle it on their own two times. In this article I will just tell you about the main problems and how to quickly resolve itself.

Why is it sparks

excellent standards

The most simple and banal reason for the discrepancy may be the size of the plug-pin standard socket. This problem stretches since Soviet times when it was in use two standards: (FROM) - Soviet and Schuko. So in the second standard pins thickness of a few more and so this plug will pretty tight in the socket of the Soviet standard. But if the Soviet plug is inserted into the socket of the standard schuko, the contact is loose, and for this reason you will be sincere.

The way out of this situation is precisely the replacement of old elements, whether the socket or plug on the new standard.

Extremely low quality of the outlet

Just cause may be the installation of sockets of extremely low quality of Chinese manufacturers. Because in order to sell the product at a low price, they save on everything: on metal, plastic and mounts. This all results in what would seem a new socket, may well spontaneously issue sparks.

there is only one solution, the replacement of the outlet for better from trusted manufacturers.

"Fatigue" wiring

Often, we operate a network of more than a dozen years. And in those days, when it was made, the load was minor. But every year, devices that consume electricity in the house, it is becoming more and there comes a time that the wiring can not cope banal. Therefore, if you know that the network is rather shabby, it is not necessary here to include large appliances (eg electric furnace). Here we must make a full audit of the wiring and replace it if necessary.

The weakening of the clamps

In absolutely any product where there are clips, screws and bolts, with the passage of time weakens tightening, because of this, the previously reliable contact becomes less dense that the sticking forks can produce sparks.

It needs revision outlet, about which we write in detail below.

Overcurrent

It is also fairly common cause, which arises due to the carelessness of the people themselves. After each outlet is calculated for a certain amount of current, and if during this operation exceeded parameter, the socket will begin to overheat, which can cause it to reflow and more tragic consequences. It should therefore be attentive to the choice of new outlets and operating old.

For example, you have a socket 16 A, so it is able to withstand a load of 3.5 kW (this figure is obtained from A ratio of 1 that corresponds to a power of 220 W) means a powerful boiler 5 kW in the outlet is not necessary include.

revision outlet

So, have you considered the main reasons why the spark plug and determined that the cause is the weakening of the clamps (This is the most common defect in the wall outlet) and this problem you will be able to cope on their own, literally half an hour.

To do this, you need pliers, screwdriver, and an indicator or multimeter.

Important. Before any work is absolutely necessary to disconnect the wiring network. To do this, go to the distribution box and turn this area of ​​your home, if you have a common machine, then turn it off. Then we come to the wall outlet and use a multimeter to check the indicator or the absence of tension, and that's only then start to work.

After switching off the machines take a screwdriver, unscrew the outlet cover and proceed to broach all contacts. After that, we take the Utica and presses the jaws (this should be done, if the socket is not self-biasing contacts)

After pulling fasten the cover and turn on the machines. All of you here and we made a revision of the socket and extend its service life even for a very long time.

Dear Reader, my article was useful and interesting?! Then be sure to Put thumbs up, subscribe to my RSS feed ENERGOFIKSIK and share articles to social services. networks. It is very important to feel your support. After all, it will create even more high-quality materials. If you have any questions or suggestions, here is my email: [email protected]