Bench garden: quickly and easily

None of the garden is complete without a bench: it is there you can admire the scenery cherished and enjoy spending time in good company. Of course, you can buy a nice shop, saving time. However, the products created by the hands, will be different from the others and will be the subject of your pride. Participants of the forum "Home and cottage" tells how to make a simple and at the same time the original benches.

From the simple ...

The forum participants Arin-ka and Sveta2609 fashioned benches and a country-style, using materials that are easy to find: the stumps, lumber pieces, stain and varnish.

Polishan presented their work - the original garden benchesWhich will decorate any suburban area. One of them - the seat and backrest of rough wood, but because the product looks naturally and beautifully. Supports for the benches are an old wagon wheel.

Bench to avoid being hit the road together with the owners and their guests, small wheels are fixed pieces of wood. The second product - no less than amazing and simple to manufacture: a normal board put on unusual support from burnt wood.

Another forumchanin fashioned benches and coffee table from old crates neighbor's shed. Uncircumcised board he was going to throw it away, and resourceful master had found them to good use: dried and fashioned a corner that looked harmoniously in a country house.

Marsha also proved to be a thrifty housewife and needlewoman with extraordinary imagination. The farm has found a heavy board and semi-circular rectangular plate. Her mistress sawed, and erected near the entrance to the house an elegant bench: legs - birch brevnyshek, back - of woven willow branches.

Sergey290 prototype of their product spied on in the store. As befits a creative person, the idea has been redesigned and improved: instead of small shops with shaky legs turned out good-quality bench: legs - from a bar 140x90, back and seat - Flooring, which a plane sostrugany protruding parts.

ANTI-killer used the stump of an old tree, which has long been in everybody's way at the site rot and spoil the view. A couple of hours with her daughter, an assistant - and now ready to cozy corner: a stump bark removed, expelled from it populate kozyavok, bottom impregnated with antiseptic, and on top - the wood-tool. By stump nailed the old floor boards, trim and planed.

Tables, molds made of hemp, borrowed from wood stocks, and tabletops - from the left after cutting Spila. Since the time of the device beds were small stones, which complete the formation of the picture. The sole acquisition of the money was a nail. The result is a beautiful and functional.

Dgusepe shared one more easy and quick to manufacture bench: the product - of intersecting bars. Fastening screws and crosses, which creates increased stiffness. Dimensions bench: seat height - 450 mm Depth - 450 mm, height of 50-60 mm back, back angle - 75 degrees, the length - arbitrary.

If benches length more than 1500 mm is necessary to increase the cross section transverse backrest bars.

Member Forum produced Mtngr shop of thin logs: Curved empty on the armrests and backrest, made of flat feet and a large board - seat.

... to the complex

Nafanya came up with a more complex product. The base produced from a bar 100x100 mm. Sharp corners on the front of the saw cut and "flunked" grinder. Initially planned screws fasten the boards at an angle, but then decided that it will be noticeable and ugly. Therefore, I acted differently: collect base with purlins drill 8 mm meter M8 studs.

The most difficult was to maintain vertical. First forumchanin Drill one passage opening. At the end faces, in the places where the stud mill made recess for washers and nuts. On one side of the stud he wore a washer, and tighten the screws razvaltseval pin. Having passed through all its bars, baited a second washer and nut, then put the second pin.

Washers and nuts need to drown in the base body, or when installing the bench on a flat surface to play, and will put the seat can not be.

Seats nafanya first fixed wooden slats, and then proceeded to the decor. The seat is rounded off at the edges, on the back with the help of patterns, drill and jigsaw pattern made, the inner edges of which handled a router, creating a contoured chamfer. The back attached to the base of two planks, carved in waves. Then I picked up a comfortable back angle, pointed and secure with screws. Bench covered with tinted protective varnish composition and the marina.

Andreevev doing bench of lumber residues. You will need: circular saw, screwdriver, the jointer and a hammer with nails. The product can be just a few hours to do to provide them with drawing.

DIMDIM proposes to make the bench on a metal frame: to disassemble the chair frame to cut it in half, to choose the suitable metal tube (or use of the second frame of the chair), the spacers welded in to receive the width of the benches 120 cm of planed boards make the seat and backrest and color.

DSP1 bought and rail profile, inventory stones. Dimensions bench front passage - 180 cm, the radius of the front - about 220-250 cm.

manufacturing sequence: remove soil, pour foundations pedestals (approximately 70h40h30 cm). On the fresh concrete put the first row of the core tables - 2h0.5 bricks, sticks around four bar reinforcement (Dmitri - 12 mm) so as to obtain axle rib webs between about 30 cm after welding.

We wait until the grab. We lay out a few series, impose profile on edge. Dmitry bent profile 40h25h1.5 gas. Checking the level of welded arc. Bandages twice on the pedestal pieces of rebar (WAB57) so that then all close the stone. Too much cut off, paint the arc. Test-fit and close up stone by inserting drawer. Flower boxes and take out podmazyvam inside. Fasten the rack to the center peg scoring circle. In their end is the layout on smaller screws.

Subscribe to the channel and put the "Like" so as not to miss the next release!

Do not agree with the author, or find a mistake in the article - write about it in the comments!