Built on a metal frame

Metal framework for toilet at the cottage party forum Mishael761 done for the day. The size of the base made of 2x3 meters, the height of struts - two meters, the roof slope - 40 cm. Itself toilet occupies the right part of the building, the rest given over to a garden store for tools and garage for scooters. The same technology, but with a triple frame, house erected 6x6 2x4 m and shower m in the base and the floor of granite.

Technologyconstruction

First installed vertical racks of thick profile. from outside the pipe 40x40 then allowed horizontally two belts (15 cm above the floor and the same - the ceiling). These zones vertically welded profiles of 20x40 for the outer skin. After tightly stacked three layers of insulation (foam thickness profile). Location of internal and external pillars of nowhere does not match, made with an offset through-metallic cold finger there.

Compared with the thermal profile difference in price - significant: almost twice cheaper.

Calculate the amount of metal per

house-hozblok by using the 6x4 scheme, which drew forumchanin. The height of the pillars is selected individually, the distance between them for a rigid sheathing is 1 meter, for siding - it is necessary to put or OSB sheathing 50 cm.

That it was not through freezing, the foreman advised the owner to fasten to the studs inside the bars, inside sheathe OSB or plasterboard, the outside - what want and fill in the gaps with polyurethane. Mishael761 prefers to cut foam or immediately insert a sheet of 1x1 m - it's faster, easier and cheaper.

For buildings more 2x3 m or necessary to do the foundation rests on three points (not 4 - winter to avoid violating the plane and the construction is not swayed in the two diagonal supports walking).

For the base used shower plate integral with the armature welded to the lower perimeter of the frame. Flooded flush with the bottom tube (a base - the profile of the frame 80h40, the others - 40x40). Plate thickness is 25 cm. Draining of the shower owner did flexi hose through the wall, the floor. Next comes the plastic pipe.

Roof: all wooden elements are fastened to the metal-drilling drill 3mm and tightening the screw on the metal. It is better to use a network screwdriver.

It should take into account such nuance: as the thermal expansion coefficient of wood and metal is different, you need every board screwed to iron crates separately and wide. If the tie bar along, screws can shatter and strong winds tear off a piece of the roof. In Mishael761 it happened with the roof of the garage.

Insulation is laid inside the outer skin after.

Materials and the cost of the toilet:

• profiled tube 40x40 - 14 m stands for 2, 8 pieces - 3 m (about 60 m) - 75 rubles per meter, the base used 40x60, little expensive;

To reduce the cost of construction can be used in place of 1.5 mm to 2 mm and with dimensions 20x40 - turn rudder 45, in general - 4500 rubles.

• proflist - 8 sheets of 2 m with the profile C8 - 500 per leaf total - 4000 rubles;
• profile sheet "slate wavy" - 6 pieces of 500 rubles in total - 3000 rubles .;
• rivets - two full pocket;
• the door to the toilet and in the technical department, in the latter case - welded grating with a sheet outside, about 500 rubles;
• peat toilet with PVC tank 60 liters and two branches - 4100 rubles;
• Bank-priming paint - about 100 rubles .;
• protective structure from rust - 25 rubles.

TOTAL - about 12,000 rubles plus the board of old buildings, if to buy new - will take about polkuba on the floor and crate.

Subscribe to the channel and put the "Like" so as not to miss the next release!

Do not agree with the author, or find a mistake in the article - write about it in the comments!