Plaster of film: an exclusive dekorativka for a penny

The easiest way to create invoices in the interior

With the advent of modern interior materials wallpaper though not ceased to be the most popular trim options, especially when the task is to make "cheap and cheerful", but much surrendered their position. Becoming increasingly popular variety of decorative plaster, due to its versatility allows to obtain the effects of weight by using the same composition. Most often, it is an imitation of any natural surfaces, stone, fabric, and even metal, and the severity of the relief depends, basically, on the fraction present in the composition of the abrasive.

However, the cost of compositions with fillers, as well as some difficulties when applying and creating a pattern, a significant disadvantage, a daunting potential consumers. But to get the desired relief is possible and at a lower cost, and a method of applying much more tolerant of fans.

Acrylic plaster and polyethylene

The use of expensive compounds in the marble chips and marble flour, special stencils, prints, roller and trowel - rather, it is the prerogative of professionals. And for the walls in the apartment, room or area, you can do the simplest materials and tools.

• Acrylic finishing putty - Finished in buckets expensive; if there is a breeding experience, you can take a gypsum plaster finish and shut acrylic primer (finished or diluted concentrate).
• Primer - a deep penetrating power, but without the filler, putty and without abrasive adheres well to the surface.
• Spatulas - can and trowel work, but it's not the cheapest tool, and for applying the basic layer through which relief will be created quite sufficient, and two spatulas (for one artist).
• Polyethylene - film area about half should exceed the area of ​​a finished surface.
• Paints, waxes, pearl - depending on the desired effect.
• Rollers, sponges, brushes - depending on the decorative layer.

surface preparation

From the quality of substrate preparation directly depends on the decorative and durable plaster, it must necessarily be strong and steady. Deletes all previous finishing layers - old wallpaper and paint is easier to depart if moisten the walls with a weak solution of primer, it is more efficient simply wetting with water. After some time, the remains easy to clean off the spatula. Cracks and potholes pre-sealed with the starting lineup, primed surface thoroughly. After the primer has dried, if necessary, at the junction of the place of plaster already trimmed the zones glued masking tape.

Application of the plaster, creating a relief

Starting to apply the plaster on the angle ending in the opposite, small spatula plaster is applied on a large and a large distributed along the wall. The entire wall should be covered in one go - leave a piece or half the next day is not recommended. If you still have not mastered, makes the "ragged" line of the descending layer - the finishing touches on tearing. This will make the transition between fragments less noticeable, but it is better to invite the assistant and pass the wall during the day. Ideal smoothness is not required, but the layer must be uniform, about 2 mm thick.

Creating a relief as possible and using the film in one hand, but also easier together - one polyethylene imposes on the application of the plaster, the second holds a residue does not adhere to arbitrarily. Begin to form a pattern, like plaster - with angle, applying the film and creating on it folds strongly crumpled film will invoice expressed.

Do not use too dense polyethylene with them more difficult to work, but if you want an easy "pozhamkannost" he is just a theme. Conveniently, a film plaster longer stays wet, and on careful consideration of the relief enough time, you can first go through the whole surface, and then add the "frost" in the right places. Depending on the variety used plaster wall will partially ready after 12-15 hours after which the film is removed. If the layer is thicker in some places turned, and the plaster is still wet, finishing lay until dry.

Another embodiment of creating relief by polyethylene - does not overlay film on the wall, and coating the entire surface by impressing crumpled plastic bag or crumpled piece film. The relief is obtained less homogenous, with the characteristic "spikes", is formed when the plaster layer stretches a film upon peeling off. In its original form it does not look very attractive, but if after a bit smooth texture, it turns interesting.

finishing

Variants of such decoration plaster weight - it is coated with wax, stained in one or more tones, fragmentary lightens. The wax is applied by roller or sponge if plaster was colored in the mass, using a colorless or glossy when white plaster, it is first stained. An interesting effect is staining in two ways - first a relief, but after a smooth roller. The first pass will fill the paint all the potholes, and after treatment with a smooth paint roller will be only in relief. To achieve the effect of antiquity, first plaster painted in full color, and after a while the paint is still wet, it neatly removed from the speakers folds of cloth, or after drying, lightly pass sandpaper, obtained characteristic abrasions.

When it comes to refurbishing, repairing cracks may be insufficient, and require more careful preparation, read, how to align walls. For lovers of smooth, marble coverings - article of Venetian. Interestingly the minimum budgets and presentable - find out how liquid wallpaper make your own hands. In the video - ideas The original interior design the famous exhibition.

Subscribe to the channel and put the "Like" so as not to miss the next release!

Do not agree with the author, or find a mistake in the article - write about it in the comments!