Installation of the furnace and the chimney

After searching the Internet for information about what is needed in the furnace lodges and how to build a chimney for it, raking Mouse came to the conclusion that his house is suitable oven Breneran (Buleryan) 01. A chimney, he decided to put the "sandwich" type.

When selecting a model - 01, he thought that the house has not insulated rooms and need additional protaplivanie. Oven predatory Mouse took a reserve of power, in order to have enough, if necessary, to heat the house in winter. So we had to think carefully about where to put the oven. And after thinking it was found the optimal location for the stove in the house. As soon as the location for the stove has been determined, it is thought through and drew the future location of the chimney, which you can see in the drawing.

delivery of materials

All work on the installation of the furnace and the chimney itself decided to do while on vacation. And before that, he began to count - how to accurately derive the chimney through the wall, and what type of chimney choose.

Still remained a problem - how to bring the oven, because it weighs 100 kg.? After much doubt Predatory Mouse has decided to do everything alone. In the store, buying, helped her load the Chevrolet-Niva. And in the country, he unloaded it himself, without donos postorenney assistance and set in the house.

Behind the stove and pipes, he went 2 times. First bought a stove and all the necessary accessories for the chimney. And then he had to buy a stand under the furnace, glass furnace. To buy flue pipes, adapter, tee, wall bushings, insulating filler - wool, fasteners to the wall and headroom. All metal that he bought was made of stainless steel.

After walking through the market, and comparing prices, predatory Mouse decided not to take a tiny metal reflector size of 0.5 m - 1 m 500 rubles, and acquired galvanized sheet size 2 2m - 1 m for 560 rubles everyone. It was enough for him to be protected from the heat of the stove wall, on the floor under the stove, and still left to cover the roof of the well.

Beginning of work

The place for the installation of the pipe he had little, so everything had to rely to a millimeter. He needed to derive the chimney through the wall and to install the pipe vertically upward so as not to interfere with the edges of the two roofs. In addition, the pipe should be installed away from the window. All calculating, he went to work.

The main and crucial moment predatory Mouse considered manufacturing support bracket under the chimney, because it has to rely all the chimney tees and other items. Support bracket for chimney predatory Mouse made itself of an angle of 30 mm and 50 mm using a drill and grinder using bolts of suitable length and diameter M10 M8.

And before that, he had to dismantle the wall, to strengthen seats for the bracket from inside the house. Then he assembled the outer bracket and attach to him two corners from the top in the form of runners - to be able to move the tee when fitting, that is, to push the entire chimney from the roof. After assembly and installation - the fitting of the supporting arm - he covered it with lacquer on metal, and to protect it from the effects of corrosion.

Satisfied that performed outside the house, began to insulating walls inside the house, but first fixed basket made of stainless steel bushings.

From the furnace wall to wall turned 35 cm - it is permissible norm given the fact that there is heat reflective screen. Therefore, he continued to work, and closed up the wall 10mm plywood and plywood across the area secured with screws asbestos sheet (worked in a respirator). Then, over the entire wall of asbestos has covered unibody sheet 2 meters size galvanized metal for 1 m 20 cm. But first he cut in this sheet, square hole for the box-anus. All fixed the screws with different kind of heads (flat or semicircular - looking where to use them).

Place in the oven predatory Mouse also well insulated from heat. First laid out on the floor tiles and fix it with screws on the edges and corners. Then spread a top sheet of asbestos and asbestos sheet spread on top sheet of thin basalt wool. Everything is covered galvanized iron sheet of appropriate size and well secured with screws suitable size. Along the edges of the sheet, he made a side that would not debris from the wood echoed through the room, and remained on galvanized sheet (where it could be easily swept away with a broom).

Thus, preparing a place in the oven and chimney, he began to collect the entire structure together. Drilled in the adapter from the furnace to sandwich the required hole - put on the adapter, and sliding the oven, - put the sandwich adapter 50 cm long. Thus all compounds was sealed with fire-resistant sealant, who bought the furnace. It took all the seams of the chimney - just one tube of sealant.

When assembling the chimney consider the requirements of the location of the direction of the flow of water and smoke. That is - collected from the bottom up (clothed upper part to the lower). In calculating the height of the chimney above the roof it is strictly guided by the corresponding SNP-s. Since chimney predatory Mouse arranged at a sufficient distance from the ridge of the roof, he made it just below the ridge. Therefore, the length of the chimney turned less than the recommended 6 meters. It happened one meter shorter. Accordingly - 5 meters - and five pipes sandwiches.

The pipe from the stove out from the wall of his house at a sufficient height above the ground. Therefore, the height of the chimney is sufficient. Lower flue segments it is secured to the wall by means of standard wall bracket, wherein the inside as well reinforced and strengthened seats for these brackets. But the upper segments in the form of three tubes sandwiches - were unfastened.

The result was a high design. And I thought he decided to insure it. Secured upper portion of the chimney three extensions, each of 120 degrees from each other. Was bought by the respective cable and special tightening clamps, hooks versatile thread for stringing cable. The ends of the ropes were attached by means of special brackets to the end walls. Only after that the chimney stood firm and motionless on his pedestal - support bracket.

Chimney passes at a sufficient distance from both edges of the roof and not in contact with them. Simply put, raking Mouse perfectly timed and everything done perfectly.

Drilled holes in the legs of the furnace, and the tiles on the floor pobeditovym drill, he fastened to the floor of the oven long bolts, and then the furnace and chimney gathered together.

Three days of waiting predatory Mouse completely dry fire-resistant sealant, and only then decided to heat the oven.

He first studied the instructions for use of adjusting valves and the first time to heat the oven to maximum. Particularly not set up the duration of combustion, so it works just over 6 hours. The first time was a terrible stench, paint baked. In general, the burns that had burned out and burnt.

The temperature outside was 19 degrees - indoors under rose 40 C. so keeping the windows and doors open, which would erode the smell of burn draft stove. Break in the oven was successful. Particular attention is paid to predatory Mouse seats can become hot near the entrance to the box. But then everything was fine.

So that the furnace was burned in the normal range. Second time raking Mouse to heat the oven literally the next morning, because at the end of June it was cold in the morning, about 12C. Then he it to heat for about 9-10 hours of instruction on the same tab. Thrust into the furnace was good - it means the chimney is exposed properly.

Most predatory Mouse was afraid that he did poorly insulated. Fears proved groundless.

And his cat liked to sit on the outer chimney - bask.

Total:

• The cost of furnace plants - about 30 thousand rubles;
• Installation time alone took about a week;

In general, predatory Mouse was happy with the result.

How to clean the chimney

Tar in the chimney is the same condensate which is formed in the furnace without any insulated chimney. If the flue is well insulated (sandwich), then there is no tar.

There antiquated method - for this you need to heat the oven aspen wood, and is suitable fir, alder, bird cherry. After the wood to heat - "from vampire trees" chimney cleaned, aspen peels the sticky black smoke from the chimney and the inner walls of the tube.

Discuss the article and read other materials devoted to country life you can on the websiteFORUMHOUSE.

Subscribe to the channel and put the "Like" so as not to miss the next release!