Useful content

Simple lathe wood: step by step guide

click fraud protection

Welcome visitors and regular readers. With you again Mikhalych and today we are making lathe of drills, the four bearings and a pair dostochek.

This machine model will be a good helper to those who use them infrequently. The model has no frame and consists of only two headstocks (front and back), the motor acts as a drill, hammer drill or screwdriver. Due to the absence of the frame, you can insert blank of any length, within reason of course.

If anyone has forgotten, that looks like a stationary machine.

And so we go.

Board 15 x 3, from it cut into 4 equal pieces of 15 x 15 centimeters. Here I must say that the size of the board may be other you. Not necessarily just follow my example, the main thing to understand a diagram of the device.

Next, connect the two bars together with screws. I have no board thickness of 6 cm or more, so twist the two bars together to the desired thickness.

Then we define conditional top and bottom on both bars. From the top back down 5 cm and make a mark for drilling.

instagram viewer

As you've probably figured out, we do it the front and the tailstock, and the holes marked for the axis of rotation. Here we will stand bearings.

Next, take down the drill on the bearing size. Tutu has decide to buy bearings for the drill size that you have, or buy a drill under the existing bearings))

Now the important point. We need to drill holes on both sides of the bar in which we insert bearings and here it is necessary to drill a depth equal to the width of the bearing. As a marker of drilling depth can be used duct tape, permanent marker, masking tape, well, or that you would normally use it for these purposes.

This pen we made seats for bearings on both sides of each bar. Now make a through-hole for the pin.

Now we cut two other bar of the same size as the previous oh fasten to the bottom of the headstock. They will serve as a basis.

Grandma is almost ready. The planting hole insert bearings.

Getting headstock assembly. Now we need a pin and four screws. The diameter of the stud of course must correspond to the inner diameter of our bearings. On the one hand studs cheat two nut and clamping them to one another.

Insert the pin into the bearings with bolts and similarly two nuts screwed on the other side of the headstock.

One grandmother is ready. We have a free rotating bearing pin with zakontrennymi nuts on both sides.

In the same Makar do and the second headstock, with only one little nuance. She set to work after the special nut for furniture. I do not know what it is called scientifically, but it spiked to crash into the timber and not loosen during operation.

That's just the spikes in this nut will have to bend in the opposite direction, ie outwards from the thread. It will capture our procurement and simultaneously send it to the torque of the drill motor.

Well, now we look at what happened and our test machine. We take the workpiece, which will process and drilled a hole in its ends equal to the diameter of our studs on pasterns.

Now we expose both the grandmother on a wooden bench flat surface and fix them with screws. Workbench performs the role of our bed.

Note that the distance between the attendants, you can adjust themselves depending on the length of your future harvesting, what is the advantage of such a model without own bed.

Once fixed headstock, workpiece set, pins on the headstock includes a drilled hole in the workpiece, so that this does not drovenyaka flew you in the forehead))

Now set the drill. That grandmother, which spiked acts as a master and we fix it in the chuck drill.

And of course we do support all the way to chisel. He has already been fashioned themselves from what your soul is your heart desires. It is also secure on the countertop. Just do not be lazy and do not think that, "and so goes", be sure to fasten.

Everything. Turn drill and drove voyat wonders woodwork. Only wear safety glasses.

That's the whole lathe stanochek. After working unscrew grandmother from the table and hide in a secluded place on demand.

Since you were a regular homebrew twig Mikhalych home worker. I hope it was interesting and useful. We put the husky and subscribe to a channel. According to your Laika I understand that such a presentation of the material in the images you are interested in and will continue to do interesting articles for you.

🚧 You can participate in channel development and support author. As a support, it is enough to take only 2 rubles Yandex Money, well, or how many do not mind. For me it is a good motivation to create such high-quality materials. 🚧

πŸ‘Œ heartily thank those who have provided support. πŸ˜‰

All peace and goodness!

Why do people leave their country houses and return to the city?

Why do people leave their country houses and return to the city?

Hello everyone!My last article aboutvillage of abandoned cottages in Bashkiriagot so many comment...

Read More

The master dissuaded from the strip foundation: an extra waste of money. Arguments in favor of slab with calculations

The master dissuaded from the strip foundation: an extra waste of money. Arguments in favor of slab with calculations

Foundation selection - the main part in building a house. Many people cannot understand which is ...

Read More

A place to live: the name of the worker-peasant "Pervomajskij" (continue to repair and home improvement)

A place to live: the name of the worker-peasant "Pervomajskij" (continue to repair and home improvement)

Our farm was wearing quite a workers 'and peasants' name "at Pervomayskaya". And the street where...

Read More

Instagram story viewer