Budget facade of the CAP under the Framework: with their hands
Facade - a card of any country house. Despite the huge selection of modern and proven options for facade finishes, the users of our portal is not afraid to experiment.
The experience of the participant with the nickname FORUMHOUSE ViktorBanev, who decided to elevate the old villa, wall sheathing OSB / OSB (Oriented Strand Board) with a further imitation of them fachwerk layout.
Usually everyone who decided to do something like that, first of all concerned with the question - what will happen to the CAP on the facade in 3-5 years?
Someone thinks that the plates vzduyutsya because OSB is not a finishing material, intended for use on the "street". Someone thinks that this is an option and more - is optimal from the point of view of reducing the financial cost and the possibility of self-repetition.
ViktorBanev (User FORUMHOUSE):
Or not to use GSP on the facade - opinions differ. I decided that it's worth it in terms of speed, ease of installation and low cost of the facade. Just note that the facade of OSB - is the economical option for cost-conscious gardeners. To decorate the capital structure - a house, should be applied more weathering material.
Looking ahead, we say that the facade of the OSB is already underway for the third year, and it looks like, demonstrates the next photo.
The result is impressive, and now go to practice. So, there is an old country house neuteplonnaya size of 6x8 meters. External cladding - board "dyuymovka". On top boards - painted hardboard. rework place - Leningrad region, ie, area with high humidity, frequent rains, fog and rather short summer.
Required - insulate the building from the outside and make a beautiful facade. Budget - minimum. This means working without wage-workers, using relatively inexpensive materials and technologies feasible to carry two people. Also interesting is the course of the user in choosing the ways of thinking of the facade decoration.
ViktorBanev:
The façade siding I do not like. Pall. Block-house - too expensive. The proven option using DSP (cement particle board), and a further dyeing simulation fachwerk also eliminated. Expensive and, because of the large weight, it is difficult to raise the sheets, and even more so, mount them on top. Molded - is not it. But I am what is called a crush on half-timbered and began to think how to put this idea into practice.
After going through a number of options the user has decided - as he liked to do a half-timbered facade on the basis of OSB. This, according to the user, much cheaper and easier than fuss with a DSP.
As a result, the user has come to this, "Patty" wall. From the inside out:
- drywall;
- wall;
- insulation - mineral wool packed in the layer 2, the total thickness of 100 mm;
- wind and moisture membranes;
- kontrobreshetka;
- OSB 3 fachwerk with simulated layouts.
Since total savings angle established in the top, the first thing that made ViktorBanev, virtually I laid the plates on the walls, in order to minimize them and cut waste.
Moreover, OSB sheet dimensions dictate the layout of the arrangement of decorative boards (25h100 mm), which cover plates and joints timbered mimic board.
After several intermediate layout options could come to a common denominator. Sheet sizes 224h122 cm, delivered vertically substantially completely covers the wall, and covers (board) need only to protect the joints of the vertical plates. Describe how to estimate the layout (pre-clearing the necessary size from the facade) on the example of the left wall of the house.
If you look at the picture above, you will notice that the left and right vertical set of 2 whole sheet OSB. According to the results of measurements wall revealed that the distance (remaining time period) is wider in the middle of one sheet but two. Those. - we need to sew up the wall with two runs, laid horizontally, and then close the resulting horizontal seam. To keep the symmetry of the overall design and layout, add horizontal strip on the extreme sheets and act in a similar way throughout the perimeter of the building.
Having dealt with the design layout, go to the installation plate. Work simple enough, but there are a number of nuances. First of all, do not forget that the hinged facade requires good ventilation for excess moisture output. If we neglect the ventilation ducts (gap) with access to the top of the facade, the moisture will lock inside, OSB boards that are poorly vapor is passed, and at substantially large thickness vapor permeability. Hence - the bunch of problems in the form of mold and waterlogged insulation.
The user at the top of the facade of the left slit, about 1.5 cm over the entire width of the panel.
Go directly to the installation of OSB. The thickness of the plates in this embodiment - 9 mm. This is quite enough, because sheets substantially do not carry power load. First, on the wall outside the frame fills - crate vertically set of wooden bars of 50x50 mm cross section.
Laid between them, vraspor, mineral wool insulation.
Further crate fills horizontal and respectively laid insulation (the so-called cross-insulation) horizontally. Thus, the plates overlap the joints. Then attach vapor permeable moisture proof membrane, and overlaps with the binding of joints sized tape (e.g., two-sided).
After that fills the vertical bars of 30x40 mm, for securing sheets SIR.
ViktorBanev:
Step install bars - 0.4 m, ie It obtained: 3 vertical strip on one sheet. OSB fastened with screws, 6 pieces. 1 bar. Gap was left between the sheets of 2-3 mm. Further, the gap carefully stained, though, I think that this is not necessary, because from direct contact with rain or dew ends of the plates are protected wooden plates 100 mm in width.
In addition to insulation, replace windows in the house, for which they were carried forward in frames made of planks 5x15 cm.
We then proceeded to the staining of mounted wall.
Before painting on the plate caused a moisture resistant impregnation bioprotective layer, on the basis of lacquer, on 2 sides.
Plate Further, before mounting on the wall (which is easier and faster), covered with two layers of acrylic exterior paint. At this stage, the user made a mistake, which will be discussed below, but now offer to see what happened at this stage. At the user's words, the result exceeded all expectations.
If you move away from the facade of 1.5-2 meters, it creates the impression that the walls are decorated with stucco, and understand from the street, it's OSB is impossible.
Besides the decor, summer terrace built in L-shaped timber of 15x15 cm instead of the old porch.
After that we went to finishing - half-timbered installation layout. Length planed board layouts different turns. Somewhere - 2, somewhere - 3 meters.
Diagonal jib at 2.5 m, made of one-piece plank.
Boards are drawn along the edges with screws. It turns solid, tight connection, in which does not get wet.
By contrast, the board painted in dark brown color.
Three-year operation of the facade has proved the technology. OSB panels on the ends are not swollen, the paint does not peel off. The only point that mentioned: because of an error made on a mounting stage (several plates "forgot" to process biosecurity), OSB outside covered with the fungus, which sometimes made out of paints.
Plates treated protection, mold is not touched. This error was easily removable. Plates removed and paint over again paint with antiseptic additive. A year later, the fungus does not appear. What eventually happened in ViktorBanevShow the following photos.
As they say, the result is obvious, and the cottage was completely transformed.
And in the end material is similar to the facade, with imitation fachwerk, but plates DSP, a user with the nickname of the portal Andrew Pavlovets.
Andrew Pavlovets (Member FORUMHOUSE):
Facade for 10 years. I walked across the CFB board vodoemulsionkoy 2 times, and everything since then nothing has been tinted. Paint keeps just fine. He did it all himself. DSP sawed size 1200h3600h10 mm squares with a side of 1200 mm. Otherwise, do not pick it up. The hardest part - making it the top corner pieces. We had to climb the stairs, if wrong with gashes, and cut down again. Holes for screws drilled in advance, and then their fasteners and baits, via block system lifted upward. It is difficult, but worth it.
The topic on FORUMHOUSE can learn more about mikrobyudzhetnom OSB 3 facade of a timbered. In addition, be sure to also read the section facades and facade materials.
The users of the portal will be useful article, which describes how to deal with pests of woodand both with their own hands to make a beautiful wooden facade.
A video shows the nuances of construction karkasnika facade under the Framework.
Discuss the article and read other materials devoted to country life you can on the websiteFORUMHOUSE.
Subscribe to the channel so as not to miss the next release!