Best homemade construction: selection for all occasions

Homemade users FORUMHOUSE: Killer hand earth drill struzhkoulovitel 3 pennies to shuropovorta cover, reel garden hose and drilling machine for metal

Buy or make your own? Perhaps it is this question puzzled any samostroyschik when it comes to tools and accessories to the construction of a country house. On the one hand, to buy something - toad strangling, and on the other - sorry for the time spent, and think, and whether fortunate homemade? To dispel your doubts, we offer you the 5 best solutions from FORUMHOUSE users. These homemade certainly not pierce a hole in the family budget. They have proved their efficiency, and forces any handyman whose hands grow from his shoulders.

Content:

• Manual "probivatel" soil, which is steeper earth drill
• How to make a cyclone from the vacuum cleaner and barrels
• Homemade holster for shuropovorta
• Reel garden hose from a can of paint
• Videos about home-made machine for drilling metal

1. Manual NOT drill for digging holes under the posts for a fence installation

How to dig a hole depth of 1.5-2 m to set the fence posts? At first glance, the answer is obvious - buy an ordinary earth auger or augers and drill a hole with a diameter of 150-200 mm. But what if you need to make a pit close to the neighbor's fence? Or you have to work in cramped conditions, for example, the walls of the house, where there is no crank handle conventional earth drill? There is an exit! Pay attention to the miracle-digger FORUMHOUSE user with the nickname

Harnich.

Harnich

In the late 80s, I had to put up a fence. Clayey soil on the site. I decided not to drill holes and punch to adapt, which is made on the knee, for half an hour, of what is at hand. The tool consists of two parts:

• Probivatel soil - metal square box with ribs.
• Rod - tube diameter of 3/4 ''.

I worked so - removed the soil with a bayonet spade, then, with the power tool tyuknul into the pit. Between the walls of boxes stuffed earth. Slightly shaking, I remove the tool. I knock on "schochkam" reinforcing bars or hit the foot. The ground falls out. The cycle repeats. I use tool so far. Speed ​​- 15 minutes, slowly, you can prodolbit two pit depth of about 1 m to work easier than earthy brown.. I advise you to simplify the design - to weld the edges of rigidity to the rod.

In the photo below the tool sketch.

This probivatel ground work.

For those who want to repeat the design - drawing.

Tool Harnich caused great excitement in the portal. Some users have begun to doubt the convenience of working with a miracle-diggers. Other advised to issue patent.

Putnikk62

Member FORUMHOUSE

I want to make myself the same device. That is to say, from personal experience convinced of its effectiveness. I think - this is an indispensable thing if you want to dig a hole the fence, the walls of the house, or to drill a hole next to the correct column. More videos to watch.

Harnich

At the request of users of the portal I took the video, how to work with the soil probivatelem.

Alven

Member FORUMHOUSE

And the clay will go?

Harnich

On a clean clay have not tried, but I have to plot the soil with a high content of clay. It is well stuffed in the tool. Better than dry soil. Only to beat harder.

Sergey240

Member FORUMHOUSE

I also drilled holes for fence posts. First, the usual drill drilled 1.5 meters, then went slurry with stones. Bur it does not take. Read on to adapt Harnich and 15 minutes from the rubbish, I cooked yourself probivatel. I passed with it another 50 cm.

Harnich

With his tools, I punched in the filter sump pits septic tank. Nearby stands a birch, so not particularly razvernoshsya. I'm just a little bit modified probivatel. Instead of a circular tube welded profiled tube section 20x20 mm, wall thickness 1.5 mm. tool weight decreased, it became easier to swing. Primer - a dense loam. First loosens his rod, at the end of which is welded blade of a hatchet. Probivatelya Furthermore, in such a cramped place like in the photo below, does not crawl. I think you can do probivatelem horizontal shafts for the construction of communications under way under the wall. So, I say - buy a drill, and I say, and why do I need, if there is a miracle-digger?

2. Two homemade cyclone 3 pennies

When building a house needs a cyclone. It will be useful for collecting shavings and dust when sawing boards or sanding log. Can not do without the cyclone when cutting cutting grooves in the stone walls. Not to buy a vacuum cleaner construction, do it yourself from a barrel and ordinary household vacuum cleaner.

ForceUser

Member FORUMHOUSE

I decided to make a struzhkoulovitel. Budget homemade - 1000 rubles. The vacuum cleaner is already there, so also bought:

• screws M4h20 - 15 rub .;
• screws M4h12 - 15 rub .;
• Barrel 65 liters - 759 rubles .;
• Cuff 50x40 - 9 rubles .;
• Cuff 40h32 - 19 rub .;
• 4x8 screws - 13 rub .;
• nuts M4 - 15 rub .;
• washers 4x8 -10 rub .;
• pipe 50h150 - 52 rub .;
• eccentric adapter 40x50 - 19 rub .;
• thermobonding gun - 397 rubles.

Melt raised himself from the budget, but it still is useful. Bought a plastic barrel, because if spoil it, to patch holes in the economy and use. Cyclone made 2 hours.

The steps of manufacturing the cyclone vacuum cleaner of homemade and plastic sewer pipes:

• User cut in the barrel bore.

• I insert the plastic tube and secure it with two screws.

• All cracks sealed. Inside view.

• The cover member cut a hole for the adapter. Tube inserted and glued joints Melt.

A barrel assembly.

Nodes homemade cyclone closeup.

Assembled cyclone-based vacuum cleaner.

ForceUser

Cyclone experienced old coffee spilling. All coffee left in the barrel. The dust collector is not coffee. For the purity of the experiment vacuumed the corridor. As you can see, the working design. I'm happy with the result.

Cyclone interested users of the portal and, on ForceUser showered with questions.

Fomich 25

Member FORUMHOUSE

A plastic barrel does not compress with heavy use?

ForceUser

My vacuum cleaner power 1.8 kW. If the suction pipe close hand, the drum crushes the side and bottom. In normal mode, the vacuum cleaner does not compress the barrel. On the power of 1 kW does not deform. It is sufficient for a tightening of sawdust and small pebbles. If the hose becomes clogged, then stretch and corrugation plug pulled into the barrel.

If the vacuum cleaner is a powerful, then fasten inside a plastic barrel frame by screwing the spacers crosswise with screws to the wall, or take a metal barrel, as did the portal user OstrieBrevna.

OstrieBrevna

But my cyclone. Collected it spent 400 rubles. Base - 50 liter keg and plumbing pipes. Plastic soldered conventional soldering iron + added steel mesh. Cyclone vacuum cleaner after sanding the walls of the framework. Collected three full barrels. When filling the barrels 40 liters in a vacuum cleaner bag of garbage is not going over wood dust cup.

3. Homemade holster for shuropovorta

And this idea for skilled workers who want to make their own hands for the gift-samostroyschika husband. Holster for shuropovorta - irreplaceable thing when working at height. With it, the tool will always be at hand.

g8o8r8

Member FORUMHOUSE

During the season you have to be fully prepared. So I made a holster. Screwdriver hanging armpit. How it to make, it is clear from the photo.

Holster assembly.

Pattern to the holster.

Place the image on a sheet of A4 borderless.

And this bag on the belt of the old backpack. The firm does not?

4. Reel garden hose from a can of paint

To wind and unwind the hands of a garden hose, it is still fun. Come to the aid of the coil to the garden hose. But their prices bite, so most of DIY made them out of what is at hand.

Ivici

Member FORUMHOUSE

I made a coil hose to use the empty jar from the impregnation of wood for 10 liters. You can even take a trimming sewer pipe diameter 160-200 mm, but the bank caught the eye. Frame of welded metal angle, half-inch pipe and fittings. Axis - rod 12 mm in diameter. Sidewall cut from plywood 8 mm thick. Dressed axle and welded washer with holes. The washer is attached with screws to a plywood sidewall. Sides screwed on the screws.

The coil is wound 25 m hose 3/4 ".

5.video ofhomemade drill press vise, which is steeper than the Chinese

Almost all domestic masters dream of a drilling machine. It is indispensable in the manufacture of homemade and in general, is always handy on the farm. After all, the convenience of work, he beats the usual drill. The only thing stopping the purchase - the high price of branded models and poor quality low cost Chinese units. What to do? Make a drilling machine with their own hands, using spare parts from domestic cars.

Sanek-Berds

User Forumhouse, manufacture drilling machine, in no way inferior to the factory model

I did a drill press vise, and for him. Drill on it is much more convenient than a drill. Copes with large diameter drills. For making it necessary for me:

• 18-th channel by the frame;
• 8-th channel to guide the rack;
• moving part - the steering rack of the car VAZ 2108;
• pulley belt transmission - motor pump of GAS 53;
• three-phase motor, converted at 220 V power - 270 W;
• jaw chuck of a hand drill.

The machine I have done without turning operations. Here are my tools:

• Bulgarian;
• drill;
• welding inverter.

Also, the user fashioned homemade vice to drill rod, made of metal residues.

• The dimensions of the clutches of 160h175 mm.
• Sponges are taken from the farm cultivator, incisions are made grinder.
• Screw the grip - long bolt M14.

More details about grip covered in the video.

And this video, which shows a turnkey drilling machine and the master tells about his technical nuances.

Below is a video which shows a drilling machine in operation. The user drills metallic square section of 28x28 mm. The diameter of the drill bit - 5, 8 and 15 mm.

conclusions

We told you about the cost of self-made instruments and devices that will be able to repeat any handyman. The main thing in such works - a great desire, invention and ability to work with a basic set of tools. On FORUMHOUSE collected 1 1000 and an idea for a DIY. We are sure you will find what you need. Share your experience. Create topics, upload photos, videos and drawings of your DIY and ask if something is not clear from our experts.

Of DIY, do not pass by! In the subject - Garage custom home designThere are dozens of devices and tools for working with metal, wood and leather.

We recommend the article:

• Reception for the Bulgarian inclined disc - Universal homemade stand for angle grinders with rotary mechanism, Eccentric clamp and cuts in a metal two planes.
• Homemade profilegib for 2000 rubles: Fotoinstruktsiya of independent manufacturing inexpensive profilegiba of parts from old cars, threaded studs and channels.
• 2 budget option improvised travorezok: how to make their own hands an inexpensive shredder for grass, Leaves and foliage of an old grinder and galvanized water tank.

In the video, a set of tools necessary for the construction of a frame house.

Subscribe to the channel! Join craftsmen FORUMHOUSE!