Useful content

Ruff for cleaning the chimney with his own hands

click fraud protection

Increasingly, the heat source in a private country house or a furnace which has its advantages and disadvantages. One of the drawbacks is that the chimneys are overgrown with soot, resulting in furnace efficiency drops, and the smoke comes into the room. To address the shortcomings must be periodically cleaned from the chimney to form a deposit.

To solve this problem, you can call a specialist or buy a ruff for chimney cleaning. However, the cost of the finished solution starts from 2000 rubles. Ruff can produce their own hands, as will be discussed in this article.

Necessary materials

For manufacturing ruff for cleaning the chimney, we need:

1. The tip of the broom.
2. Tin.
3. Lead (about 1 kg) available from the battery.
4. Bolt (about 80 mm in length).
5. The ring nut (nut with eye).
6. Cable 2-3 mm (height 1.5 m chimney +).
7. The cable clamp (1 pc.).

used tools

To assemble the device for cleaning the chimney from the soot, you must have the following tools:

1. Drill (screwdriver) with a drill.
2. Hacksaw.
instagram viewer
3. The key of suitable size for installation clamp or pliers.
4. Clippers.

For the preparation of liquid lead will need:

- Bank;
- Fire;
- grip for banks for transfusion lead into the workpiece.

Instructions on making a ruff to clean the chimney

1. Take the tin and the center hole is drilled for the bolts.

2. The bolt is installed inside banks, passing out through the threaded bore.

3. Jar with screw place firmly on the ground (the bolt will be shipped to the ground).

4. Kindle the fire, set by the Bank for molded, lead and melts it, periodically pouring it in a jar with a screw.

Caution when lead smelting (melting point 327 degrees), so as not to get burned.

5. Cut off from the broom bush for fixing handles and the center drill in the core hole for the bolt.

6. Once the lead has cooled down, it is necessary to connect the weighting agent (bank with bolt, filled with lead) with a broom. For this breed bristle broom to the side with which they are installed, and a significant effort of pushing the broom, are seeking to bolt went into the hole drilled in the broom. Then twirl eye nut. Performing this item will require a large effort. Bristle broom must stay in the horizontal direction or close to it.

7. Clippers bristles shorten, to obtain a diameter smaller than the diameter of the pipe was 0.5 cm (if it is larger, ruff not enter the tube and is wedged therein, and if the diameter is smaller, the cleaning efficiency will decrease).

8. Skipping rope through the eyelet screws and fasten its grip.

When cleaning the chimney follow when working at height safety.

Benefits

At firstThe main advantage is the low cost of manufacturing a brush for cleaning the chimney.

Secondly, Metal bristle factory ruff will leave scratches on the steel walls of the chimney, which in turn will reduce the service life of the pipe.

helpful hints

1. Better to take the cable without braid. Cable using unwound and then wound up again, so braided and sprinkled crack. If stored properly no contact with water and the need for protection against corrosion. Cable without protective braiding is cheaper.

2. Canning of the bank should be at least 3 cm smaller in diameter than the chimney, but not less than the diameter of a broom bases. These conditions must be observed that in the case of skew the device is not jammed in the pipe and did not require additional washers for flattening broom bristles.

3. Since a nut with an eye, the bolt should be chosen with the condition that its length does not interfere with the assembly. It is possible to use several screws of different lengths, either periodically shorten it, but then the manufacturing process may be delayed. Applying the minimum required bolt length, it will be harder to assemble the device, as flattened the bristles will try to regain its footing, and will need to apply force to the connection bolt nut.

When using longer bolts time to take the broom bristles of a new direction will be at least a day. Thus, a day will need to disassemble the connection, shorten the bolt and tighten it as much as possible again. This procedure is repeated as long as the bristles will not accept the horizontal direction.

Subscribe to the channel, the only way you will be informed of new publications - in front of a lot of new and interesting information!

p.s.: We try to give you the most important, useful information. If you have been interesting and useful, please put "like".

What should not be added to seedling soil

What should not be added to seedling soil

Growing seedlings is a responsible and painstaking business, which novice summer residents do not...

Read More

A universal way to mark the foundation

A universal way to mark the foundation

The beginning of the construction season is not far off, but somewhere it has already begun. At o...

Read More

Why grass grows on the roofs of some houses in Norway

Why grass grows on the roofs of some houses in Norway

Norwegians have long been supporters of using natural, clean materials to build and improve their...

Read More

Instagram story viewer