Cheap and beautiful fence with his hands

How to make a durable and decorative fence edging board

For each landlord one of the topical - fence portion. Sometimes fences appear among the first, when the house is still in the project. Sometimes owners think about the fence to complete the construction and planning, it is sometimes necessary reconstruction or complete replacement of the obsolete in every respect the fence. But, in any case, you always want to receive, and an attractive and relatively inexpensive fence that will stand for more than one year. Wooden fences on metal pillars are quite common. This checkerboardAnd the fence, and the different variations of the edging boards, for example, from one of our craftsmen with the nickname buka23. He made a fence of burnt edging board, which will be discussed in the material.

Content:

• Materials.
• Mounting pillars.
• Preparing the timber.
• Implementation of the idea.

materials

buka23

Member FORUMHOUSE

I tell its fence - an area of ​​15 acres, the length of the perimeter fence 110 meters. Columns three meter from the profile pipe 60 × 40 × 2 mm, are prepared. Covered with epoxy primer, which is usually protected by metal constructions (bridges, pillars), lowering further paced bituminous mastic.

For filling flown craftsman acquired unedged board joiner natural moisture in an amount of 6 m³. Immediately after the purchase Okoro, processed Vitriol and folded in a pile with a lining for ventilation. This is one of the most important moments - thanks vitriol processing board is protected from pests and blue stain. Moreover, the same tool will help transform the already diseased wood microflora. buka23 I discovered this on his own experience and buying party lumber (plank 150 × 30 cm to 2 meters long) to the vertical.

buka23

I want to say more about Vitriol - because of the beginning of the summer season, anywhere and at any price did not work to buy a board without hitting the blue. But qualitatively covered vitriol, after drying for 2.5 months, it looks like new! True, the board gets dingy gray-yellow hue, but it is irrelevant before firing. 1/10 sulfate is diluted with water and applied liberally with a brush.

Mounting pillars

After examining the thematic section of the forum, craftsman decided to abandon the concrete in favor butovaniya. Drilled hand drill (200 mm) holes with a pitch of 3 m, a depth of 1.3 m, a layer of gravel to fall asleep 10 cm, and set zatramboval poles. Layers of sand and gravel by pouring the rammer and the wells filled to the top. Steel poles firmly, "as a stone."

As is often the case, sensible thoughts come too late: after the installation of its pillars craftsman thought about the durability of poles and how it will have to change them in ten years due to insufficient wall thickness. Those who are still being prepared, he recommends the following:

buka23

We need a fence for decades - just think of the respective supports. What I come: optimally pipe tubing with wall thickness of 5.6 mm or 7, ground cover and protect the bitumen. It is almost a century. If cheaper - wooden beam 100 × 100 mm, burn intensely and fluff, but actually impregnate pine tar and linseed oil. When installing do without betonirvaniya only rubble backing for "ventilation". It is not necessary to deal with the forces of frost heaving - it is easier to level.

Preparing the timber

After two and a half months, when the boards thoroughly dried out, buka23 calcining engaged via balloon gas burner, hand and common sense. For one weekend burned all the boards vertically in the amount of eighty pieces, decorative happened even without the application of the planned infiltration.

Further under the burner and skillful hands were six-meter board.

A deposit of the board for mounting to poles laundered brush by hand, six-meter cleaned with high-pressure washing.

Before applying the impregnation better to wait a couple of days, although the sun washed the burnt board dries in a few hours, but we are talking about pre-dried wood, not initially wet.

Impregnation of wood user bought technical linseed oil - the first layer are coated board it abundantly clear oil, the second layer is applied to oil, with addition of wax. As regards the proportions, the wax tree does not spoil, but in view of the cost of a decent weight fraction thereof is first reduced to one hundred grams per liter of oil, and plans to reduce it to fifty grams. According to estimates, and this amount is sufficient to protect the wood from the environment.

Recipe for impregnation for the second layer:

• Melt wax in a water bath.
• Pour into hot linseed oil.
• Protomai on fire, not boiling, within two or three hours.
• When excessive viscosity of the resulting composition to dilute it turpentine to a desired consistency.

The topic arose a debate about the method of application - to accelerate and simplify the process of offering flokovye roller. As explained more experienced comrades, the rate - not the main thing.

Green0568

Member FORUMHOUSE

Roller fat layer does not nanesesh and pine and all such breed after firing absorb much oil. I even larch practically filled, and the brush is needed to disperse the oil on the surface. It is better to remove the excess, than to pass several times.

In buka23 oil consumption turned about 4-5 l / m², since one board is almost like a sponge, and some almost saturate, depending on the structure and firing intensity. About 2/3 of the total volume leaving the first layer.

Regardless of the purpose of use of wood, whether or fence facade of larch, necessarily "promaslivat" on both sides.

implementation of the idea

Force majeure has not been canceled, and finish with a fence at a construction season did not happen. The first stage, except the installation pillars finished processing the entire timber volume (m³ 6) a first layer of linseed oil. It took seventy liters a week and brush work from morning till night.

Deposited board folded in the same stack through the pad and covered with roofing material from precipitation - a board with a dry method works.

The subject matter also discuss ways to mount the board to the metal post, and one of the participants offered his own version.

vip_makar

Used a bent pin in place, any difficulties in fitting. Doing so in the absence of fusion, would welding - welded plate. What about reliability - the third year in normal flight. Strength confirmed "inspection force" - pulling up on the finished structure without consequences.

While the author of the theme was not able to continue the work, inspired by his theme and adopting the technology of its preparation of wood, other craftsmen embody ideas in life.

AnnaRich - as a think tank, with the teenager, the son as an artist, used the "instructions" and are grateful to the author for the creative approach and detailed presentation. They are very happy with the result.

Also, the fence of baked board made the above techniques glpower- edged boards 150 × 25 mm was calcined roof burner, washed with high-pressure washing and linseed oil coated in a single layer.

himself buka23 plans to continue the construction of the fence already next spring, but unplanned downtime made it possible to dismantle and sell the "doubtful" columns and order instead of the pipe tubing 73 mm. Boards which have lain in a pile a year, generally in good condition, but in places the sun getting discolored. What made craftsman to reflect the addition of a pine tar oil in the cooking composition to the second protective and decorative layer.

That he will succeed, we learn in the spring, and those who want to connect to a discussion - in the subject of the author. Off-budget, but beautiful - "Openwork metal fence ...". From the article about 3D-fence can be found, how to save on the fence, not losing as. In the video - the house of baths and a unique fence.

Subscribe to the channel to join FORUMHOUSE!