Entry group to fame: DIY Gates

Fotoinstruktsiya on the construction of the entrance to the site with a group sewing the gate and the gate tree

Fence. Goal. Gate. What to do them? How many people, so many opinions. From expensive stone structures, to "people" and all the boring on trapezoidal sheet metal poles. If the soul needs something such, that do not pass by. This article describes how to make their own beautiful and inexpensive swing gates with a wicket on the tape foundations.

Content:

• How to make a foundation at a high water table under the swinging doors on brick pillars
• As a self-cook Gates and sew them tree
• Answers to questions concerning the construction of an entry group
• How much is done by hand swinging doors and gates

Homemade swing gates and gate on brick pillars

DyadyaVovan

user FORUMHUSE

I decided to fence the land. I began with the construction of swing gates and wickets. Gates want to automate. Long thought how or what to do. I invented - zalyu tape. I put it on three brick pillars. Gates are welded from profile pipe. Then sew them to the board.

The final version of swing gates with a wicket.

The basis of the gate - foundations - concrete weakly deepened tape proposed by the portal user Groundworkturf.

This foundation is not vypret forces of frost heaving.

Steps show you how to make these gates:

• Mark out and dig a trench under the strip footing.

• Lay on the bottom of the trench with a geotextile overlap the walls. The "trough" pour gravel. Tamp the gravel layers. The total thickness of the "cushion" of about 30 cm.

Crushed better rasklinit, for example, by driving to a fraction 20-40, fraction 5-20.

• Install formwork and tie the reinforcing cage.

• Part of the 'tape' wiring for driving hinged gates.

The wire is laid in IPA tube 25 mm in diameter, and multilayer pipe diameter of 16 mm.

• Tie the rebar for reinforcing pillars.

• Fill the strip foundation under the gate and gate.

• Buy Gate hinges.

• Parts and fittings of mortgages for welding weld hinges to the pillars.

• Fold the pillars of brick.

User engaged in laying the first time in my life. "Bricks" made of Unmodified DyadyaVovan I laid on the square of the "top ten". rod length - 45 cm.

Turned out neat seams.

• Put mortgages under the gate and the gate hinges.

• Fill the inside of the pillars peskobeton and output wires.

Poles are ready.

Now weld the gate and gate. To get straight gate without distortions,first weld solid design, and then grinder, cut it into two separate flaps.

• Prime the color and the gate leaf and the gate.

• Hang the flap gate.

• Fabricate and Grout two stops for wings open gate.

In future DyadyaVovan welded to the posts of security sensors.

Do not forget to bring the wires.

FORUMHUSE advice from those who are planning to install drives for swing gates — just make them under the mortgage (from the yard). Otherwise, then have to mount the metal plate to the bricks, and he eventually crack due to cyclic loads.

• Embed the gate lock.

DyadyaVovan

Hint: start with the tie-in of the castle shaped tube. It's easier than messing with the final wicket. And I missed the point of connection to the castle. As a result, the handle rested against the porch, and the gate was not closed. 30 minutes thinking what to do. Cut off the finished painted porch and cook new, or in this groove to make a handle and lock. I decided to make a groove. Cut portion of the tube place and brewed metal strip. Podshlifoval, primed, painted. I liked the result.

• Obsheyte Gates board.

Pre-drill holes in the boards for wood screws and cover impregnated in two layers.

So that the water does not stagnate on the ends of the plates, washed them down with a slight slant. Top and bottom taper outwards.

• Make a latch on the gate.

It is ready for entry group with caps mounted on poles.

How to make folding gates and gate: answers to the most frequently asked questions

Goal DyadyaVovan like the users of the portal. They asked questions about the master.

Mishanina

Please tell me, what size of profile pipes?

DyadyaVovan

I bought a trumpet,

• Section 60h40h2 mm - 24 m;
• Section 40h20h2 mm - 18 m;
• Section 40h20h1,5 mm - 24 m.

Mishanina

And what is the height of the posts and the fence?

DyadyaVovan

Gate poles about 2 meters. Fence And he made from welded mesh. The height of the fence will be 1.8 m.

Mishanina

And as you reinforced the foundation and how much cement is gone?

DyadyaVovan

Reinforcement of the foundation - 2 rows of rods 5 + 5 pcs. transverse frames. Together, with a laying it took 15 pillars cement sacks of 25 kg. Fittings "ten". It spent on foundation 72 m and 24 m poles.

How much is your own hands to build swing gates and gate

Dimensions group entry:

• gate width - 90 cm;
• Door width - 3.9 meters;
• the width of the whole structure - 6 m.

Total on swing gates and gateuser spent 28 thousand. rub. Rates - Fall 2018.

conclusions

Make a beautiful fence, sliding or swing gates can anyone who is friends with the tool. Practice shows that it is cheaper than hiring a builder or pay a "company." Do not forget about a significant plus - "mercenaries" chase footage on the speed and quality you need.

If you came on and want to build their own makeshift gate and fence, we suggest topics: Foundations for fences and Gallery of wooden fences.

Helpful articles:

• Building a fence made of profiled sheet: load calculations and the installation features. Selection algorithm and materials calculation of wind loads acting on the fence made of profiled sheet.
• Fence edging the board with their own hands. technology and the stages of self-construction of beautiful wooden fence section.
• Budget sliding doors with their hands. manufacturing experience and drawings cheap and simple sliding gates.

In the video - A fence made of gabions - non-standard solution for the modern home.

Subscribe to the channel! become members of FORUMHOUSE!