Budget shredders from scrap materials: their own hands
Fotoinstruktsiya: how to make their own hands an inexpensive shredder for grass, leaves and foliage of an old grinder and galvanized water tank
Thinking what to do with the grass you mowed the area, foliage, stems and tops? One of the options - chop "gratuitous resource" and to put it into action. Compost or food for small zhivotinku. To do this, you need travorezka. You do not want to overpay for a store? Manufacture of her with his hands, an inexpensive, as did users of the portal.
Content:
- Homemade travorezka "Monster" from Bulgarian and galvanized tank
- Shredder grass with the engine and kukuruzoluschilka «Made in USSR»
- Features of operation of DIY and ways to improve them
Travorezka own hands driven grinders
Tok2Z
user FORUMHOUSE
I grow up in the country birch. With trees fall foliage. It is necessary to clean up, burn, score the compost pit. Foliage long rots. I decided to grind it. This requires travorezka. Looked, the master on the Internet. I am including the brain and that's what I did.
Do you like the low-cost version of its garden shredders? Read the article on and learn how to make home-made from Bulgarian and metallic tank. Tok2Z It proceeds as follows:
- He thought, than to turn the shredder knives. The choice of small - to put the engine from the washing machine, or buy an electric motor. At the user's words - the engine from stiralki weak and acquire trohfaznik, and remodel it into a single phase, did not want to.
- Tok2Z I bought in the market for 2 thousand. rub., the old grinders, 2 kW and knives on lawnmowers for 700 rubles. I ordered from Turner bushing, spending another 500 rubles.
- Cooked frame put on it from the water tank galvanized. Assembled structure and included travorezku.
Tok2Z
Turnovers crazy. He threw a shovel pot leaves, and they blew! I check where there is a stream. With the edge of the tank goes up air and sucks in the middle. Cut the ring from galvanized and installed in the center of the tank. He threw foliage. Knives crushed her right, and she flew into the bottom pipe.
To chop the grass into very fine fraction, the user has set to "exhaust" chimney corner.
Travorezka grinds the leaves directly into the compost pit.
Compare: a pile of leaves.
Chopped leaves.
Tok2Z
Travorezka thresh everything - grass, leaves. Sometimes, with the foliage comes wire. Pebbles. metal pieces. Stones chopper chops. No iron. Falls off, look for trash and throw it away. The roar in this terrible. Among the shortcomings - thin tank wall. Punches. I will redo it. I do tank of the iron sheet 2.1 mm thick.
Universal travorezka and kukuruzoluschilka
Alex Hk
user FORUMHOUSE
I also did travorezku. Mainly used for grinding herbs for poultry. Basis homemade - killovatny motor, made back in the USSR. I bought for 1400 rub. Works great. Three-phase engine, but redesigned to work on a network of 220 volts.
Making homemade travorezki steps:
- Turner machined flange.
- The flange holes drilled and tapped.
- Knives made from a piece of old rusty two-handed saw.
- Blades fastened to the flange.
- Travorezki a frame manufactured from metal sheet 4 mm thick. For square metal strip welded section 4x40 mm and being bent around the circumference. In the center of the frame drilled hole.
Alex Hk
I bent strip hammer blows to the metal on the jaws. The radius of a circle controlled by drawing it on the frame.
At the finish of the user welded to the bottom of the legs. An electric motor secured. I made a big pot with a lid that of travorezki, during engine operation, went out the garbage.
Buck, for ease of use herb grinder, removed.
Finished products.
Kukuruzoluschilka of travorezki
Alex Hk I decided on the basis of travorezki, to make the mechanism for peeling corn. I turned the unit "two in one". To make a home-made necessary:
- Cut from a metal disk.
- Drill a hole in it for the M6 bolts.
- Transform base to the orifice is at the bottom. And the grass is ground finer, and corn is not chopped into chaff.
- The disc fastened to the flange.
Side view.
Buck altered. He was joined by "reflector" for the release of corn "cabbages" into the bucket.
Inside view.
Travorezka-kukuruzoluschilka assembly.
Finished products.
Storage space for mounting.
That the grass is not wound on the motor shaft, the user has set the protection - ring.
Dismantled travorezka-kukuruzoluschilka.
Alex Hk
Experimentally found that the best option shredding grass - two knives. Four knives convert the grass into a mess. More pounding apples for birds. One bucket of crushed apples for 4-5 minutes. Travorezka turned-vegetable cutter-fruktorezka.
conclusions
Make travorezku afford most home masters. As the tank using "jar" from the oil, and so the barrel. D. For the manufacture of home-made, you will need a set of tools:
- Bulgarian;
- drill;
- welding inverter;
- set of handtools.
The main expenditure part - the engine. Members used the b / y drives. Is it profitable to do travorezku their own hands? Compare prices for the factory model and figure out how much it will cost you to buy components for homemade. Do not forget to add a time cost.
Want to learn more? Ask the author travorezok Topic Homemade Travorezka "Monster 2015".
Recommended article:
- Fotoinstruktsiya on independent manufacturing profilegiba for 2000 rubles of parts from old cars and bicycles, bearings, threaded studs and channels.
- 5 variants goat for sawing logs for firewood - cheap home-made tools for sawing logs on a block of wood and firewood: drawings, constructive experience of use.
- universal homemade stand for grinders a rotary mechanism, eccentric clamp and cuts in a metal two planes.
In the video - how beautifully decorate karkasnik own hands.
What do you use to facilitate manual labor?
For more information on this and other topics can be found at FORUMHOUSE. Become a member of the most famous portal of the country life and the construction!